An annual inspection of your unit can ensure that the various potential problems mentioned above are detected early, and before they require complete replacement. During this inspection, for instance, a professional might find small cracks in your heat exchanger or a faulty seal in your blower motor. Some manufacturer's warranties even require these annual inspections to maintain validity. Typically, your furnace inspection will cost between $80 and $150 depending on the area in which you live and the professional you work with.

Regarding your post, Every technician performs a maintenance differently. Today's modern furnaces really don't require as much maintenance as older style systems did. For instance: Older furnaces had drive belts, pulleys and motors with oil ports.Today's blowers are direct drive no belts, no pulleys, sealed bearing motors no oiling required. All of the new modern technology cuts the maintenance time in half if not more. Today's equipment has multiple safety's in place so that in case of a failure the system will shut down. non serviceable control boards or (Brains) monitor system functions. Unlike oil systems, the maintenance on a gas system can possibly be completed in less than half the time. I'd say 20 to 30 minutes is about right unless a service issue arises. In the 30 minute time span, the doors can be removed, system components can be visually inspected, the flame can be inspected and co test can be performed for spillage and vacuum of the combustion area can be performed if needed. The air filter should be checked and the humidifier can be activated. Remember that probing into a perfectly functioning system can be detrimental to its lifespan. My advice is change you air filter, keep the area around the equipment free of dust and try not to store in close proximity to the heating plant. Be sure you have an updated quality carbon monoxide detector in your home. Regarding the crack in your heat ex-changer, If the heat ex-changer had a crack in it, the system it should have been shut down right then and there. Be aware that Carbon monoxide may be entering your living space due to that crack. Have a knowledgeable company come back and do a CO test in your home at the supply vents and use a scope to check your heat ex-changer for cracks. I hope this helps you. Bottom line, you have to trust the company that you are using. If you feel uncertain about their capabilities, then more than likely, you instinct is correct. Good Luck to you.. Happy Holidays
As a Kansas City Heating and Cooling company, Anthony’s professional technicians are not only friendly, but extremely skilled. No matter what the problem with your air conditioner or furnace is, they can solve it. But don’t wait until there is a problem. Enroll in our annual service program and we’ll keep all your equipment maintained so you get the most out of your furnace, air conditioner, and plumbing equipment. An ounce of prevention is worth a pound of cure, so our service program pays for itself.
On average, furnace repair costs $287 nationally, with some homeowners spending as little as $60 while others paying $900 for furnace maintenance. Repairs to an electric furnace can run you $300 or less, while gas furnace repairs can be more complex and range from $375 to $1,200, depending on the what needs service. Most homeowners spend between $131 and $453 to fix their furnace. Here is what you need to know, along with the various factors that could affect the price of your furnace repair.
@Neil What is the use of repeating lessons when there is so much more to be learned? Technology has moved on from the adz. Plumbers use PEC, insulation is sprayed, glue-lams allow for open floor plans and furnaces are no longer stoked with coal. As for the new people, if these trades cannot attract fresh blood we will all be unable to get homes built and repairs made. I don't yearn for my first home with the leaky concrete block foundation, failing well pump and an oil furnace held up by the plenum. I'll take heat pumps, solar panels and PVC waste pipes any day.You can get all the sill plate repairs and flitch beams demos you need on YouTube.
When a furnace maintenance is performed a combustion analysis should be performed to identify any problems that couldn't be found by a visual inspection. You want to know what the Carbon monoxide level your furnace is producing as well as the oxygen/CO2 levels and stack temperate. The analyzer will also give you a calculated efficiency rating with the information the analyzer receives. You should have >100ppm of Carbon monoxide output during normal operation of your gas furnace. When you have higher numbers or CO numbers increasing during operation their is a problem with the furnace the technician should then find the cause of. This is just a brief explanation I'm trying to get across to those who get their furnace maintained and to those who don't! Check to see if anyone in the company has a NCI certification for carbon monoxide/combustion analysis.

Furnace Service Company

×