Our team is NATE-certified. North American Technician Excellence represents the entire HVAC industry and is an independent, third-party, non-profit organization. NATE-certified technicians are skilled professionals who have verified real working knowledge of HVAC systems through specialized exams. Whether your heating or cooling system requires routine maintenance or complex repair, the NATE-certified team from Nerthling's Heating and Air Conditioning shows up on time, prepared to complete the job quickly and accurately, without unnecessary multiple house calls. We work on all makes and models and offer affordable and convenient service plans to protect your equipment from wear and tear, and ensure like-new performance.
There’s a common misconception that you can save money by shutting the vents (supply registers) in rooms that aren’t being utilized. Resist the urge to close too many, as doing so can actually increase the pressure in your furnace, making it work harder to heat your home. This can lead to failed blower motors, mold or mildew in your ductwork, damage to the compressor, a cracked heat exchanger, and other problems. What Does a Furnace Tune-Up Include?
I was very happy with the heater service I received how ever I also signed up for handy man work and they were flakes so I am still looking for one that will come out to my house and look at the work to give me an estimate. I am a motivated home owner who ndesperately needs work done. The heater guys were spectacular as well as Lori at the special order desk.
We live in a recently completed townhouse that was built with double-wall construction. That construction method was touted by the builder as what would keep sound from penetrating between the units. But we can hear the next door neighbors' TV and stereo, and sometimes voices and even snoring, through the wall. While sometimes it's the volume, mostly it's the bass sounds coming through the wall. They say they don't hear us, but we keep our bass turned down. They crank up the bass, and they are not going to change that. They also are not going to do anything construction-wise to help from their side. What is the best way for us to try to block the low frequency/bass sounds from penetrating the existing wall into our side?
Start with your utility company; they can help a great deal. Comparing previous bills isn't always a good measure, as the weather is never exactly the same month to month. Instead, if you take your energy bill and divide it by the square footage of livable space in your home, don't count areas like unfinished garages or basements -- you can calculate how much you are spending to heat or cool each square foot of your home. Your energy provider can tell you what the average cost per square foot is in your region for that same period of time so you can compare apples to apples.
Inspect your furnace thermostat by first making sure that it’s turned on. Also, ensure that the thermostat switch is turned to “heat” and not “cool”. If your furnace will still not start with the thermostat on, try adjusting the temperature settings to a few degrees higher. Inspect any visible wires for breaks or splits, and make sure your thermostat batteries are not dead. Do not touch any open wires; contact a professional.
Though forced-air furnaces are normally quite reliable, they can break down. To avoid break downs, it pays to know how to take care of your furnace and fix it when something goes wrong. Inevitably, a furnace stops working when you need it most. Consequently, fixing becomes urgent very quickly. The following instructions will help. With a little do-it-yourself experience and the proper guidance, you can troubleshoot and repair a variety of furnace problems yourself.
When your air conditioner is installed by a qualified Kirkland air conditioning installation technician, you can count on a reliable, effective performance. It will be properly sized for your home, and any ductwork will be expertly designed and installed. If you really want to be the heat this summer, then a professional air conditioning installation is your only option.
2Be sure the furnace’s circuit breaker is on or that its fuse has not blown. Check both the main electrical panel and any secondary subpanels that supply power to the unit. If the circuit has blown or tripped, reset the circuit breaker by flipping it all the way off and then on again. Or replace the fuse. If the circuit blows again, there is probably a short in the electrical system providing power to the furnace. For this, you may need to call an electrical contractor.
• Furnace is making more noise because it’s turning on and off more frequently. It may need repair, may not have been sized properly to fit the needs of your house, or may not have the airflow available that it needs from the ducts. The ducts are most often the culprit. Sometimes adding a cold air return can solve this. Ensure your vents are all open. If you are closing off vents in your house this can contribute to the issue.
The US Environmental Agency recognizes geothermal heating & cooling as the most environmentally-safe, cost effective heating and cooling system on the market. A typical 2000 square foot home can be heated or cooled for as little as a dollar a day. As one of the biggest and most experienced geothermal companies in the Cohoes area, Choice Heating & Cooling has the resources, expertise and practical knowledge to design and execute this groundbreaking technology, enhancing home comfort and energy savings
Call on Marky Mark's Heating, Cooling & Plumbing, LLC for high quality work, every time. We give our customers the personal attention they need to ensure satisfying results. Whether you require HVAC installation, seasonal maintenance, or skilled repair, our highly trained and experienced technicians focus on energy efficient, reliable, and long-term operation.
Great article! I am having trouble identifying what to use for the aluminum or zinc strips to prevent organic growth and staining. How wide are the strips? Are they predrilled? I am starting to see black stains on the north facing asphalt shingles. Do you recommend treating that befor adding the metal strips? If so, 50/50 bleach and water or a commercial product?