If your furnace has a pilot light, look for the flame. Check your owner’s manual or the instructions posted inside the furnace cabinet for step-by-step lighting instructions. Usually this involves first turning the gas valve to Off and waiting a couple of minutes. Then you turn it to Pilot. Next, press and hold it down while you light the flame. Last, wait a minute or so, release it, and then turn it to On.
Lennox was started to provide some of the most dependable, reliable HVAC systems in the field while providing great service and quality for customers. B & B Heating & Cooling in Florissant is no different, with our constant devotion to your comfort and commitment to the community. We strive to be the best at what we do so you can always be comfortable, and know you can always depend on us. Give us a ring at 314-838-9800 or schedule an appointment with us so we can help you achieve whole home comfort. 

You can, however, avoid many serious damages to your AC by scheduling your air conditioning repair as soon as you notice a problem with your system. No irregularity is too minor to contact a professional Kirkland air conditioning repair technician about. The longer you wait to schedule AC repair service, the more likely it becomes that your system will be seriously compromised.


Attic Fan Installation Bathroom Fan Repair Ceiling Fan Installation Ceiling Fan Repair Electric Wall Heater Installation Electrical Panel Installation Electrical Panel Repair Electrical Panel Upgrade Electrical Wiring Installation Electrical Wiring Upgrade Exhaust Fan Installation Holiday Lighting Installation LED Interior Light Conversion Light Fixture Installation Light Fixture Repair Light Fixture Replacement Light Switch Installation Outlet Installation Outlet Repair Spa Wiring Installation
You might guess it from the name: the heat exchanger is the part of your furnace that actually heats the air your blower motor pushes through the furnace. It consists of a chamber in which the heat energy produced by natural or propane gas is transferred to the forced air. At the same time, this part also includes a vent through which the gases themselves are safely removed from the unit and the air that enters your home. Because of these gases, a problem with your heat exchanger needs to be dealt with promptly. Over time, cracks in the exchanger can result in carbon monoxide leaks. Taking care of the problem once again means understanding the existence of a range: repairing your heat exchanger can cost as little as $100, but a full replacement may cost up to $1,200.
More often than not it’s because we’re afraid of high costs of service and finding the right company we can trust. When you choose Signature Heating, Cooling & Plumbing, there’s no need to worry. Rest assured our qualified and trained technicians can handle any type of service repair to maintain a quality of comfort your family is used to. We schedule your appointments with a date and time that can fit with your scheduling needs. We offer high-quality services at fair prices, giving you the best value for your money.
Seattle furnaces can run nine months of the year. Based on the average temperatures in our area, if you compared running your furnace to a car it would get the equivalent of 1.8 million miles over its expected lifespan of 15 years. Your heating system will work hard for you, but like your car, doing routine and regular maintenance will keep it running smoothly, avoid problems, and keep your warranty intact.
In the combustion chamber, fuel mixes with air and is ignited, generating heat—as well as carbon soot, water vapor, carbon dioxide, and worse. A buildup of soot can cause the chamber walls to corrode. Richard scrapes out built-up carbon using a small wire brush. Then he removes loose material with an industrial shop vacuum and inspects the chamber for holes or corrosion before replacing the cover.

What happens when you have an emergency? The first reaction of most people is to panic. When a furnace stops working, you need it fixed and fixed immediately—especially in the middle of a cold, Ohio winter. That need can make people feel as if they are at the mercy of the repair company. That is why it is so important to call a company you can trust and rely on—Jennings Heating and Cooling.


If your furnace sputters to a halt during the evening or overnight in the middle of winter, you can bet that the indoor temperature will plummet by morning and everyone will be cold and uncomfortable. It isn’t as bad as outside because you have wind protection and residual heat, but no one in the house will be happy. The key to finding a quick solution to these kinds of scenarios is to align yourself with a reputable, reliable service provider before there is a problem. If you have a local expert in your corner, you can call as soon as something happens and your service disruption will be minimal.
Your furnace's flame sensor is essentially a safety mechanism. As a thin metallic rod in front of the flame inside the unit, it's sole purpose is to confirm that your gas valves only open when a flame actually exists to burn that gas. When the flame sensor stop working, on the other hand, gas leaks can occur. To repair your furnace's flame sensor, expect to spend between $80 and $250. Even a full replacement of this part typically does not go above that range.
Regarding your post, Every technician performs a maintenance differently. Today's modern furnaces really don't require as much maintenance as older style systems did. For instance: Older furnaces had drive belts, pulleys and motors with oil ports.Today's blowers are direct drive no belts, no pulleys, sealed bearing motors no oiling required. All of the new modern technology cuts the maintenance time in half if not more. Today's equipment has multiple safety's in place so that in case of a failure the system will shut down. non serviceable control boards or (Brains) monitor system functions. Unlike oil systems, the maintenance on a gas system can possibly be completed in less than half the time. I'd say 20 to 30 minutes is about right unless a service issue arises. In the 30 minute time span, the doors can be removed, system components can be visually inspected, the flame can be inspected and co test can be performed for spillage and vacuum of the combustion area can be performed if needed. The air filter should be checked and the humidifier can be activated. Remember that probing into a perfectly functioning system can be detrimental to its lifespan. My advice is change you air filter, keep the area around the equipment free of dust and try not to store in close proximity to the heating plant. Be sure you have an updated quality carbon monoxide detector in your home. Regarding the crack in your heat ex-changer, If the heat ex-changer had a crack in it, the system it should have been shut down right then and there. Be aware that Carbon monoxide may be entering your living space due to that crack. Have a knowledgeable company come back and do a CO test in your home at the supply vents and use a scope to check your heat ex-changer for cracks. I hope this helps you. Bottom line, you have to trust the company that you are using. If you feel uncertain about their capabilities, then more than likely, you instinct is correct. Good Luck to you.. Happy Holidays

Great article! I am having trouble identifying what to use for the aluminum or zinc strips to prevent organic growth and staining. How wide are the strips? Are they predrilled? I am starting to see black stains on the north facing asphalt shingles. Do you recommend treating that befor adding the metal strips? If so, 50/50 bleach and water or a commercial product? 

Heating Repair Company

×