When your furnace needs a repair, trust the professionals at BGE HOME. We’ll show up on time and in uniform, and fix your furnace correctly the first time. Plus, our technicians are available 24-hours a day for emergency repairs . To schedule a furnace repair online , use the link below and have peace-of-mind knowing that a licensed, certified HVAC technician will have your system up and running as quickly as possible. For 24-hour emergency furnace repair service, call 1-888-243-4663.
As a Kansas City Heating and Cooling company, Anthony’s professional technicians are not only friendly, but extremely skilled. No matter what the problem with your air conditioner or furnace is, they can solve it. But don’t wait until there is a problem. Enroll in our annual service program and we’ll keep all your equipment maintained so you get the most out of your furnace, air conditioner, and plumbing equipment. An ounce of prevention is worth a pound of cure, so our service program pays for itself.
@Neil What is the use of repeating lessons when there is so much more to be learned? Technology has moved on from the adz. Plumbers use PEC, insulation is sprayed, glue-lams allow for open floor plans and furnaces are no longer stoked with coal. As for the new people, if these trades cannot attract fresh blood we will all be unable to get homes built and repairs made. I don't yearn for my first home with the leaky concrete block foundation, failing well pump and an oil furnace held up by the plenum. I'll take heat pumps, solar panels and PVC waste pipes any day.You can get all the sill plate repairs and flitch beams demos you need on YouTube.

I was disappointed with the pressure of a tub and shower that were plumbed with 1/2 supply lines (2nd floor). Could be low pressure from the street, but I want to replace with 5/8. Plus, I'd like to have 2 back to back showers, one inside and one outside. So, I had intended to bring a 1 supply to both, then branch up to valves and shower head with 5/8. Finally, I thought pressure from the street was typically 55 to 70 psi and I am concerned if pvc can take that.Any thoughts?


As touched on by their name, heat pumps function by transferring heat energy indoors during the winter and outdoors from your home during the summer. They're often attached to air conditioning units, using the surrounding air to transfer energy. However, geothermal heat pumps and water source heat pumps are also available. The cost to repair a heat pump, again, depends on the specific problem. Replacing a faulty thermostat may cost up to $300 including labor, while a worn or damaged defrost control board can set you back up to $600. For more details on your potential repair costs using this heating source, visit our heat pump repair cost guide.
This job involves removing the access panel, loosening a couple of bolts that hold the blower motor at the proper tension, and adjusting its distance or realigning the belt. In many cases, it’s a good idea to remove the belt and buy a replacement at a home center. Last, when reinstalling the belt, be careful not to over-tighten it; this can wear out the motor bearings.
Richard checks for holes in the exhaust flue that could leak carbon monoxide, particularly where the pipe meets the furnace. Small holes can be patched with foil tape, but corroded flues must be replaced. He also adjusts the flue pipe's barometric damper, which moderates the chimney draw. "A big, tall chimney in an old house tends to suck too much air, compromising efficiency," he says. "Your service pro can weight the damper to lessen the draw.
We don’t just repair and replace existing equipment, either. We also do upgrades. Summers get hot and winters get cold here in Kansas City, KS. If your water heater, furnace, or AC unit just isn’t cutting it, we can install a new one. We always offer the best price on new equipment, including easy financing options. Call us for a free estimate, and if you decide the price is right, we’ll send out one of our expert technicians to install your furnace, AC or water heater.

As a Kansas City Heating and Cooling company, Anthony’s professional technicians are not only friendly, but extremely skilled. No matter what the problem with your air conditioner or furnace is, they can solve it. But don’t wait until there is a problem. Enroll in our annual service program and we’ll keep all your equipment maintained so you get the most out of your furnace, air conditioner, and plumbing equipment. An ounce of prevention is worth a pound of cure, so our service program pays for itself.
I was disappointed with the pressure of a tub and shower that were plumbed with 1/2 supply lines (2nd floor). Could be low pressure from the street, but I want to replace with 5/8. Plus, I'd like to have 2 back to back showers, one inside and one outside. So, I had intended to bring a 1 supply to both, then branch up to valves and shower head with 5/8. Finally, I thought pressure from the street was typically 55 to 70 psi and I am concerned if pvc can take that.Any thoughts?
Whether you have an electric or gas furnace, you shouldn’t have to suffer when your heater is not working. At Sears Home Services, our technicians fix many of the top furnace manufacturers. The issues you may face with your furnace can vary depending on the type of heating system. If you own an electric model and it isn’t working, some of the potential causes include:
Furnaces and thermostats are not mix-and-match appliances. Using the wrong type of thermostat with a furnace will cause operating problems and can be dangerous. Although thermostats look similar, they are designed very differently. There are numerous types of heating systems and thermostat systems and they need to be coordinated for safe and proper operation. There are three types of thermostat systems used today: millivoltage, low voltage, and line voltage.​
×