AAA Heating and Cooling has been the leader in residential and commercial furnace installation, heating services and air conditioning repair for thousands of clients throughout Portland, Beaverton, Hillsboro, Lake Oswego and the surrounding areas for over half a century. As a family-owned Portland, OR business, we offer a variety of services, including the installation of home heating and air conditioning systems, AC and furnace service and repair, duct cleaning as well as a variety of commercial heating and cooling solutions.
Yes. You should expect to pay a diagnostic fee to cover the cost of the technician's visit, the diagnosis of your air conditioner's problem, and a quote for the repair options. You will be advised of the issue along with recommended options to correct it, which may include a system replacement if your unit is old or significantly damaged. If you decide to replace the system, the diagnostic fee will be credited toward your replacement purchase.
This job involves removing the access panel, loosening a couple of bolts that hold the blower motor at the proper tension, and adjusting its distance or realigning the belt. In many cases, it’s a good idea to remove the belt and buy a replacement at a home center. Last, when reinstalling the belt, be careful not to over-tighten it; this can wear out the motor bearings.
Moncrief provides a wide range of services from high-quality energy-efficient systems, tune-ups and inspections, as well as repairs in the Roswell and Marietta areas. As a full-service heating and cooling company, we stay up-to-date on the most economical and energy-efficient systems available for your home or business. In addition, our technicians are well-trained in a wide range of systems to provide quality and cost-efficient furnace service, repairs and installation.
When your gas furnace isn’t blowing hot air, the issue could be due to a faulty pilot light or broken ignitor. Remove the furnace cover panel and visually inspect whether you can see a flame from the pilot light. A natural gas furnace will be blue and yellow in color, and a propane furnace should have a bluish green flame with a yellow tip. If you can see a flame and it appears normal, the issue could be related to the furnace blower motor or other complex furnace parts. If the flame appears low or non-existent, it’s best to contact an experienced furnace repair company. Remember to never touch any open wires; contact a professional.
When it comes to heater repair in Denver, a properly serviced system means significant savings for the homeowner. When a Denver heating technician inspects your system before the winter sets in, the first thing they will check is the condition of the air filters. These filters are important, because they are responsible for removing contaminants, allergens, and dust particles from the air every time the system is turned on. When the filters are clogged, expect more particles to easily pass through right into the air you breathe inside the home. The Denver heating experts will inspect and replace any filters that are no longer effective.
With more than 100 years in the industry, Lennox has continuously provided industry-leading innovation and technology while preserving strict durability and reliability standards. The specialists at House of Heating Incorporated help bring those standards to Marshfield so that you can always maintain total home comfort. If you’re in the market for a new HVAC system or even if you just have a question about what we can provide, give us a ring at 888-384-3163 or set up an appointment with us online. We’d love to hear from you. 
"During the winter, all the air that your family is breathing comes through this filter," says Richard. "You can't change it too often, but never let it go for more than a year." Changing the filter is something any homeowner can do easily. At the same time, Richard checks the blower belt's wear and tension. (The blower, driven by an electric motor, moves heated air from the furnace through ductwork to room vents.) A loose belt can slow the blower, compromising efficiency. If the belt deflects more than ¾ inch when pressed firmly, it can be adjusted by sliding the motor backward slightly.
A number of other variables can influence your decision on whether to repair or replace your furnace, as well. In addition to cost and brand, consider the expected lifetime of your furnace. If it is more than 15 years old, it might make more sense to invest in a new unit even if it costs more than simply repairing the current problem. Long-term costs also play into the equation. For example, your new furnace may be more energy efficient than the current unit. Even though you will pay more for the actual installation, you might be able to make back your investment through lower energy bills. To make your decision, consult with a reliable professional on what to do. In inspecting your furnace, they will be able to make an informed recommendation that looks not just to the next year, but years into the future. That way, you can make the best possible decision for your home and budget long-term.

Yes. You should expect to pay a diagnostic fee to cover the cost of the technician's visit, the diagnosis of your air conditioner's problem, and a quote for the repair options. You will be advised of the issue along with recommended options to correct it, which may include a system replacement if your unit is old or significantly damaged. If you decide to replace the system, the diagnostic fee will be credited toward your replacement purchase.
If your furnace has a pilot light, look for the flame. Check your owner’s manual or the instructions posted inside the furnace cabinet for step-by-step lighting instructions. Usually this involves first turning the gas valve to Off and waiting a couple of minutes. Then you turn it to Pilot. Next, press and hold it down while you light the flame. Last, wait a minute or so, release it, and then turn it to On.

When a furnace maintenance is performed a combustion analysis should be performed to identify any problems that couldn't be found by a visual inspection. You want to know what the Carbon monoxide level your furnace is producing as well as the oxygen/CO2 levels and stack temperate. The analyzer will also give you a calculated efficiency rating with the information the analyzer receives. You should have >100ppm of Carbon monoxide output during normal operation of your gas furnace. When you have higher numbers or CO numbers increasing during operation their is a problem with the furnace the technician should then find the cause of. This is just a brief explanation I'm trying to get across to those who get their furnace maintained and to those who don't! Check to see if anyone in the company has a NCI certification for carbon monoxide/combustion analysis.

Furnace Service Company

×