*Portland Metro/Vancouver Metro/Astoria includes Beaverton, Gresham, Hillsboro, Aloha, Cornelius, Damascus, Fairview, Forest Grove, Gladstone, King City, Lake Oswego, Milwaukie, Oregon City, Sherwood, Tigard, Troutdale, Tualatin, West Linn, Wilsonville, Wood Village Sandy, Aurora, Wilsonville, Newberg, Sherwood, Donald, Hubbard, Woodburn, Amity, Carlton, Dundee, McMinnville, Sheridan, Willamina, Columbia County, Rainer, Saint Helens, Warren, Scappoose, Vernonia and Astoria.
The cost to replace your entire unit is around $4,000. That expense can range from $2,500 to $5,900, depending on the type and brand of furnace you choose. Brands particularly have an impact on that price. A Goodman electric furnace, will only cost about $2,100 for the unit and labor. On the other hand, a Trane oil furnace may cost up to $9,000 all things considered. Our Furnace Installation Cost Guide can give you a better idea on both the general cost and the differences for brands like Amana, Bryant, Coleman, and others. The brand also plays into the repair cost for your furnace. Especially the prices of individual parts can change; a York heat exchanger, for example, can cost up to $1,900, while the same component from Heil will cost as little as $400.
It can also be a health hazard. Technicians say a furnace inspection can reveal carbon monoxide leaks, which are hard to detect because the gas is colorless and odorless. Carbon monoxide can lead to headaches, dizziness, nausea and even death. An estimated 500 people die each year, and 15,000 people are taken to emergency rooms, because of exposure.
Cleaning the debris that builds up on your filters will aid with the flow of air. When your air filter is clogged, your air handler must work harder to compensate for the blockage of air flow. In addition to driving up your utility bill, the reduced air flow through your heating and cooling system can cause your heat exchanger to overheat and shut off too quickly.    
To keep your furnace in good working order it’s important to have it regularly cleaned. The national average furnace cleaning cost ranges from $60 to $80, though prices can vary greatly based on where you live in the country and what your furnace maintenance includes. An HVAC company may have different rates for different levels of furnace maintenance. For example,one company may offer general furnace maintenance for $79 and advanced maintenance for $138. Another company may offer a 38-point maintenance check for $89 and a 64-point maintenance check for $178. According to Energy.gov, a standard furnace cleaning and maintenance visit can include:

B & B Heating & Cooling offers furnace service appointments that help keep your furnace in excellent shape and running efficiently for you all year long. Whether that’s finding small issues before they become big problems, identifying potential safety hazards or making sure you’re staying in line with your manufacturer’s warranty, our experts have you covered. Our trained technicians complete furnace service with care, inspecting a number of components in and around your furnace. In fact, our multi-point inspection can help make sure your system runs smoothly throughout the winter.
BGE HOME HVAC repair technicians are thoroughly trained and certified to work on all major brands of heating and air conditioning equipment. When your system breaks down and needs a heating and air conditioning repair, you want to call someone you can trust. Need air conditioning service in the middle of the night? Emergency heating and cooling HVAC service is available 24 hours a day by calling 888-243-4663.
In a lot of homes, in Chicago Illinois, the initial HVAC installation was banged together to get it done. We’ve found big errors in heat system installations, like heat registers that aren’t hooked up and ducts that are open and pumping heat into your crawlspace or attic, or thermostats installed in the wrong place. Our Heating system technicians can survey your HVAC system and suggest improvements that will improve your comfort and save you wasted fuel bills.

As the largest heating company in the Northwest, Washington Energy Services has fixed thousands of heating systems. We service most major brands of heating equipment, including York, Bryant, Carrier, Lennox, Coleman and Rheem. Our NATE certified, factory trained service technicians are standing by for furnace service, and also heat pump and air conditioning repair. Home owners from Sea-Tac to Lynnwood trust Washington Energy Services for furnace service and repair. Schedule your service today!
If your furnace sputters to a halt during the evening or overnight in the middle of winter, you can bet that the indoor temperature will plummet by morning and everyone will be cold and uncomfortable. It isn’t as bad as outside because you have wind protection and residual heat, but no one in the house will be happy. The key to finding a quick solution to these kinds of scenarios is to align yourself with a reputable, reliable service provider before there is a problem. If you have a local expert in your corner, you can call as soon as something happens and your service disruption will be minimal.

This job involves removing the access panel, loosening a couple of bolts that hold the blower motor at the proper tension, and adjusting its distance or realigning the belt. In many cases, it’s a good idea to remove the belt and buy a replacement at a home center. Last, when reinstalling the belt, be careful not to over-tighten it; this can wear out the motor bearings.
Richard checks for holes in the exhaust flue that could leak carbon monoxide, particularly where the pipe meets the furnace. Small holes can be patched with foil tape, but corroded flues must be replaced. He also adjusts the flue pipe's barometric damper, which moderates the chimney draw. "A big, tall chimney in an old house tends to suck too much air, compromising efficiency," he says. "Your service pro can weight the damper to lessen the draw.
An annual inspection of your unit can ensure that the various potential problems mentioned above are detected early, and before they require complete replacement. During this inspection, for instance, a professional might find small cracks in your heat exchanger or a faulty seal in your blower motor. Some manufacturer's warranties even require these annual inspections to maintain validity. Typically, your furnace inspection will cost between $80 and $150 depending on the area in which you live and the professional you work with.

The cost to replace your gas furnace will vary based on the type and size of furnace you select, labor and installation costs, and any repairs your HVAC system may need. Nationally, average HVAC prices for a heating specialist range between $1,800 and $2,500. It’s important to select the right size gas furnace for your heating needs. A furnace that’s too small won’t heat your house properly, while a furnace that’s too large will run inefficiently, cycling on and off and likely breaking down sooner. HVAC specialists calculate your exact heat needs by measuring your home and incorporating variables such as the regional climate and your home’s level of insulation. Retail pricing for gas furnaces can range from $650 up to $3,000 and more. The higher the AFUE (annual fuel utilization efficiency) rating of the furnace, the more efficient it is at turning fuel into heat and the lower your carbon footprint and utility bill will be. HVAC installation costs are often based on an hourly rate and can range from under $50 to over $100 per hour, depending on the company and the furnace being installed. Higher-end furnaces cost more to install because they require added labor and expertise. For a typical installation, it might take two HVAC installation pros one day or less to remove your old furnace and replace it with a new one.
Your HVAC system is an important appliance with a limited lifetime. Depending on use, with regular maintenance you can expect your furnace and air conditioner to last between 8-18 years before you will need to replace the old one. However, poor maintenance is one of the primary reasons for early replacement HVAC systems ahead of end of average life expectancy.
A pinging or popping sound coming from the duct work can come from thermal expansion—the ductwork expanding and contracting as it heats and cools.  Or, air blowing past a loose flap of metal can make the sound. Track along the duct runs, listening for the sound. If you locate it, make a small dent in the sheet metal to provide a more rigid surface that’s less likely to move as it heats and cools.
"LIFESAVER! Came right out to our home to save us from the heat. I called around 11 and they sent someone by the afternoon 1:30. Carlos fixed our AC on the spot! Very professional and knew what the issues were and fixed them all as fast as possible! Otherwise we would all be toast in this Texas Summer HEat. Thank you Carlos with Ruben's AC! Excellent service"
×