We concentrate on providing our residential and light commercial customers with superior service, installation, and replacement of heating and air conditioning systems. Our customers can count on our expertise in high efficiency heating and cooling equipment, air cleaners, humidifiers, boilers, heat pumps and in floor radiant heating. We are a Carrier Factory Authorized Dealer. We will help our customer choose the best product for their specific needs. We are very innovative and creative when solving many heating and cooling problems, including “in the floor hot water heat” and “hydronic zone heating” for different temperature requirements in the home or commercial building.
At Bob’s Heating & Air Conditioning, we believe that our customers deserve to live comfortably throughout the entire year. That is why we offer such a comprehensive selection of air conditioning, heating and water heater services in Kirkland, WA. When you work with us, you can rest assured that your furnace is installed properly, your AC maintenance is meticulous, and that your water heater repairs are top notch. Contact us today to learn more about the heating and cooling services we offer throughout Kirkland, WA.
It can also be a health hazard. Technicians say a furnace inspection can reveal carbon monoxide leaks, which are hard to detect because the gas is colorless and odorless. Carbon monoxide can lead to headaches, dizziness, nausea and even death. An estimated 500 people die each year, and 15,000 people are taken to emergency rooms, because of exposure.
We will work with you every step of the way to ensure that you get a consistent, reliable and effective performance from your heating system. From heating installation and replacement to routine maintenance and unexpected heating repairs, our Kirkland, WA heating technicians do it all. When it comes to heating system service in Kirkland, WA, there is no time to waste. Contact us today for more information.
Marky Mark's Heating, Cooling & Plumbing, LLC offers a range of residential and light commercial HVAC services in Thornton, CO & Westminster, CO. Call 720.961.4016 to request an emergency repair, schedule yearly maintenance, or get a free estimate on a new furnace or air conditioning system. Our team of licensed HVAC technicians can address all makes and models. We offer quick turnaround, competitive pricing, innovative products, and high quality service. When temperatures start to change in Thornton, CO & Westminster, CO and the Northern Denver Metro area, call on the heating and cooling experts at Marky Mark's Heating, Cooling & Plumbing, LLC.
If your heating system in Everett, WA is not working it is likely your furnace needs repair or service. At times the fix is simple, other times it is not. Our heating and furnace service technicians have years of experience working on furnaces like yours in Everett, WA. C.M. Heating has service vehicles on call that are fully equipped with the tools and parts necessary to get your furnace back up and operating.
We don’t just repair and replace existing equipment, either. We also do upgrades. Summers get hot and winters get cold here in Kansas City, KS. If your water heater, furnace, or AC unit just isn’t cutting it, we can install a new one. We always offer the best price on new equipment, including easy financing options. Call us for a free estimate, and if you decide the price is right, we’ll send out one of our expert technicians to install your furnace, AC or water heater.
For starters, once a year, vacuum out the area around the furnace’s blower. If possible, also slide out the fan unit, clean each fan blade with a toothbrush, and then vacuum with a brush attachment on a vacuum cleaner. While you’re at it, look for oil ports on the motor, normally located near the motor shaft. If the motor has these, apply two to three drops of non-detergent motor oil into each port (you may have to remove a cover plate to do this). Though most contemporary motors don’t require lubrication, do lubricate motors with oil ports once a year. For more about maintenance, see Maintenance Checklist for Central Heating Systems.
Among the leading ways to prevent a breakdown and make sure it runs like a lean machine is with yearly scheduled tune-ups on your furnace. Just like any mechanical equipment, the useful life of a furnace will be enhanced with preventive maintenance, by ensuring that all the elements of the unit are running efficiently. In addition, regular cleanings can help pinpoint concerns before they become big problems and you end up paying emergency rates on a cold winter night. Plus, because furnaces burn fuel to make it hot, it’s important to inspect all the various pieces to ensure there aren’t any ruptures or leaks that could impact the safety of your family. Taking the time to schedule a tune-up, even when it’s not making that odd rattling noise you’ve been ignoring, will save you time, stress, and money throughout the heating season.
• Furnace is making more noise because it’s turning on and off more frequently. It may need repair, may not have been sized properly to fit the needs of your house, or may not have the airflow available that it needs from the ducts. The ducts are most often the culprit. Sometimes adding a cold air return can solve this. Ensure your vents are all open. If you are closing off vents in your house this can contribute to the issue.
Locally owned and family operated, M and M, Heating & Cooling, Plumbing & Electrical customizes solutions to perfectly fit your requirements and lifestyle. We specialize in a wide range of services including plumbing, water heating, indoor air quality, and residential and commercial temperature control. Our team of highly trained and certified technicians are fully licensed and insured, adhere to strict service procedures, and meet exacting standards of quality. Call on M and M, Heating & Cooling, Plumbing & Electrical at (720) 443-6119 for dedicated service throughout Longmont, CO & surrounding areas, and have confidence in a rewarding experience and long-term results. With over eighteen years of satisfied customers, we take great pride in a job done right.
The cost to replace your gas furnace will vary based on the type and size of furnace you select, labor and installation costs, and any repairs your HVAC system may need. Nationally, average HVAC prices for a heating specialist range between $1,800 and $2,500. It’s important to select the right size gas furnace for your heating needs. A furnace that’s too small won’t heat your house properly, while a furnace that’s too large will run inefficiently, cycling on and off and likely breaking down sooner. HVAC specialists calculate your exact heat needs by measuring your home and incorporating variables such as the regional climate and your home’s level of insulation. Retail pricing for gas furnaces can range from $650 up to $3,000 and more. The higher the AFUE (annual fuel utilization efficiency) rating of the furnace, the more efficient it is at turning fuel into heat and the lower your carbon footprint and utility bill will be. HVAC installation costs are often based on an hourly rate and can range from under $50 to over $100 per hour, depending on the company and the furnace being installed. Higher-end furnaces cost more to install because they require added labor and expertise. For a typical installation, it might take two HVAC installation pros one day or less to remove your old furnace and replace it with a new one.
Regarding your post, Every technician performs a maintenance differently. Today's modern furnaces really don't require as much maintenance as older style systems did. For instance: Older furnaces had drive belts, pulleys and motors with oil ports.Today's blowers are direct drive no belts, no pulleys, sealed bearing motors no oiling required. All of the new modern technology cuts the maintenance time in half if not more. Today's equipment has multiple safety's in place so that in case of a failure the system will shut down. non serviceable control boards or (Brains) monitor system functions. Unlike oil systems, the maintenance on a gas system can possibly be completed in less than half the time. I'd say 20 to 30 minutes is about right unless a service issue arises. In the 30 minute time span, the doors can be removed, system components can be visually inspected, the flame can be inspected and co test can be performed for spillage and vacuum of the combustion area can be performed if needed. The air filter should be checked and the humidifier can be activated. Remember that probing into a perfectly functioning system can be detrimental to its lifespan. My advice is change you air filter, keep the area around the equipment free of dust and try not to store in close proximity to the heating plant. Be sure you have an updated quality carbon monoxide detector in your home. Regarding the crack in your heat ex-changer, If the heat ex-changer had a crack in it, the system it should have been shut down right then and there. Be aware that Carbon monoxide may be entering your living space due to that crack. Have a knowledgeable company come back and do a CO test in your home at the supply vents and use a scope to check your heat ex-changer for cracks. I hope this helps you. Bottom line, you have to trust the company that you are using. If you feel uncertain about their capabilities, then more than likely, you instinct is correct. Good Luck to you.. Happy Holidays
Do you need expertise in HVAC? Roswell and Marietta residents who choose Moncrief Heating & Air Conditioning get the benefit of over 118 years of reputable experience in air conditioning and furnace repair, service and installation. Whether you have an emergency or need routine service, we are available 365 days a year. Call us today at 404-350-2300.
Furnace tune ups should take anywhere from 45 minutes to hour and a half, depending on what the technician has to deal with when he gets there. I was a heating and AC professional for over 10 years and I had tune ups that only took me 30 minutes, and others where it seemed like I had to practically disassemble the entire furnace, clean, then put back together. Every call is unique. However, it's important you trust your contractor. Your instincts are more accurate than you probably give yourself credit for. I don't remember a tune up ever going less than a 1/2 hr in my 10 years of experience. It just takes time to setup, take down, and perform the actual maintenance. If you figure a minute per inspection point, it should have at least taken half an hr. I've showed up to furnaces that look flawless, and I still take them apart and clean them because that's what the homeowner paid me for. If there is even a hint of a cracked heat exchanger, get a second opinion. There are scams out there, and unfortunately a 20 minute inspection wouldn't reveal that. Have whomever is making the claim show you via camera or by physically removing the combustion chamber from the furnace and showing you. As weird as that sounds, I've removed heat exchangers out of furnaces just to prove that there was an issue. A cracked combustion chamber can be a serious issue, so the fact that he said it should be fine says either he doesn't know what he's doing or he's not being truthful, or both. It's not that cracked heat exchangers are leaking carbon monoxide, it's that they can. It's the potential that makes it dangerous. Hope this helps!
You might guess it from the name: the heat exchanger is the part of your furnace that actually heats the air your blower motor pushes through the furnace. It consists of a chamber in which the heat energy produced by natural or propane gas is transferred to the forced air. At the same time, this part also includes a vent through which the gases themselves are safely removed from the unit and the air that enters your home. Because of these gases, a problem with your heat exchanger needs to be dealt with promptly. Over time, cracks in the exchanger can result in carbon monoxide leaks. Taking care of the problem once again means understanding the existence of a range: repairing your heat exchanger can cost as little as $100, but a full replacement may cost up to $1,200.
Wonder how much Festool is paying Silva to showcase their outrageously expensive line of tools. He used practically the entire product line on this project that was nothing more than a Festool commercial. I guess the brad nailer company didn't offer any kickbacks to the crew because you never saw their brand name. This show has turned into nothing more than crass commercialism. And when did Silva become a 'master carpenter'. He can't hold a candle to Abrams. Never could. But he's definitely better at milking the sponsors. Would love to see the inside of his workshop.
"Jorge Mondragon was very prompt and did an excellent job replacing my old heater furnace with a newer one. He explained me very well the details and specifics about why I would need a 3.5 ton furnace with the specific BTU given the square footage of my house. I would highly recommend him as he is a sound professional and very prompt in his service."