Your furnace's flame sensor is essentially a safety mechanism. As a thin metallic rod in front of the flame inside the unit, it's sole purpose is to confirm that your gas valves only open when a flame actually exists to burn that gas. When the flame sensor stop working, on the other hand, gas leaks can occur. To repair your furnace's flame sensor, expect to spend between $80 and $250. Even a full replacement of this part typically does not go above that range.
We asked This Old House plumbing and heating expert Richard Trethewey to show us the proper steps that a service professional would follow for an oil-burning forced-air furnace; the basics on a gas system are similar. In both, fuel is mixed with air and ignited, heating a sealed chamber. Fresh, filtered air then blows across the outside of the hot chamber and into the heating ducts. (Homes with radiators have boilers instead of furnaces. These heat water instead of air, but the annual checkup is similar.) In all, the dangerous exhaust from the combustion chamber is vented out a flue or chimney.
When a furnace maintenance is performed a combustion analysis should be performed to identify any problems that couldn't be found by a visual inspection. You want to know what the Carbon monoxide level your furnace is producing as well as the oxygen/CO2 levels and stack temperate. The analyzer will also give you a calculated efficiency rating with the information the analyzer receives. You should have >100ppm of Carbon monoxide output during normal operation of your gas furnace. When you have higher numbers or CO numbers increasing during operation their is a problem with the furnace the technician should then find the cause of. This is just a brief explanation I'm trying to get across to those who get their furnace maintained and to those who don't! Check to see if anyone in the company has a NCI certification for carbon monoxide/combustion analysis.
“Walter Zainey started the Greenwood Furnace Co. in the Greenwood neighborhood of Seattle in 1918 and quickly built a reputation for providing quality products and services. For years we believed Greenwood began in 1921 but only recently, May of 2017, Walter’s granddaughter shared a newspaper ad from 1968 showing that Greenwood was actually founded in 1918! When your company goes back 100 years you are bound to have mixed messages about the history but we now have an accurate founding date and founder. Thank you to the Zainey family and especially Jacklyn for taking the time to share the story with us. I am sure Walter Zainey would be proud the heritage he created is still living on.
This job involves removing the access panel, loosening a couple of bolts that hold the blower motor at the proper tension, and adjusting its distance or realigning the belt. In many cases, it’s a good idea to remove the belt and buy a replacement at a home center. Last, when reinstalling the belt, be careful not to over-tighten it; this can wear out the motor bearings.
We’re located in Florissant and service the surrounding area, so feel free to swing by if you’re searching for a new furnace or want to set up an appointment to have one of our techs visit your home and help you figure out which system is ideal for your home. Schedule furnace repair or a furnace service appointment with B & B Heating & Cooling using our online scheduler, or if you’re in need of help a little more quickly, give us a call at 314-838-9800. 

Our technicians have experience repairing furnaces and will make sure your home is back to keeping you warm and cozy in no time. From training and certifications to our reputation for getting the job done right time and time again, you can trust that House of Heating Incorporated’s furnace repair technicians will have your problems taken care of and your furnace working smoothly. Whether it’s emergency furnace repair or service you can schedule in advance, our team can provide you peace of mind, knowing that your furnace is in skilled hands. Do you need furnace repair? When performing a repair, it's vital to hire professional HVAC contractors.


2Be sure the furnace’s circuit breaker is on or that its fuse has not blown. Check both the main electrical panel and any secondary subpanels that supply power to the unit. If the circuit has blown or tripped, reset the circuit breaker by flipping it all the way off and then on again. Or replace the fuse. If the circuit blows again, there is probably a short in the electrical system providing power to the furnace. For this, you may need to call an electrical contractor.
If you use a furnace, central air conditioning system, or any other HVAC equipment relying on a forced air distribution system to spread comfort throughout your home, then the condition of your air ducts is paramount. Make sure that your ductwork is in outstanding shape so that you can heat and cool your home effectively and efficiently. To do so, duct sealing in Kirkland, WA may be necessary.
AAA Heating and Cooling has been the leader in residential and commercial furnace installation, heating services and air conditioning repair for thousands of clients throughout Portland, Beaverton, Hillsboro, Lake Oswego and the surrounding areas for over half a century. As a family-owned Portland, OR business, we offer a variety of services, including the installation of home heating and air conditioning systems, AC and furnace service and repair, duct cleaning as well as a variety of commercial heating and cooling solutions. 

Heating Repair

×