When your heating and cooling system stops working, you need the help of a reliable, experienced, local service professional that can diagnose the problem and repair your air conditioner or furnace at a fair price. You can count on The Home Depot's licensed and insured heating and cooling professionals for all your heaters, air conditioning units, and any ventilation needs.
If your home is not heated using forced air, chances are a boiler will make sure you stay warm during cold nights. A hot water system delivers hot water through a network of pipes that run to every room in your house. The heating effect gets maximized through radiators. The most common issues with hot water heating tend to be not be major, but small problems that add up over time. Mineral deposits within the water tank, a pilot light malfunction, or an issue with a radiator itself can require professional repair. On average, you will pay between $183 and $582 for these problems. The exact amount will depend on the exact problem, as described in our boiler repair cost guide.
We provide superior heating and cooling service and repair as well as HVAC system maintenance, repair and duct cleaning services. For over 20 years, Ballard Natural Gas Service has provided the highest quality services for your home. You can take comfort in knowing that we will treat your air conditioner, furnace, water heater, ducts or gas fireplace the same way we would treat our own, with the best care and highest quality professionalism. We treat you like family.

If your heater is relatively new, we will be able to repair it. If your furnace is antique, we will fix it if it can operate safely. The HVAC technician can check for cracks in the heat exchanger. Cracks can leak dangerous exhaust fumes into your living space. Sometimes, repairing a damaged furnace is more expensive and less efficient than replacing it.

Furnace tune ups should take anywhere from 45 minutes to hour and a half, depending on what the technician has to deal with when he gets there. I was a heating and AC professional for over 10 years and I had tune ups that only took me 30 minutes, and others where it seemed like I had to practically disassemble the entire furnace, clean, then put back together. Every call is unique. However, it's important you trust your contractor. Your instincts are more accurate than you probably give yourself credit for. I don't remember a tune up ever going less than a 1/2 hr in my 10 years of experience. It just takes time to setup, take down, and perform the actual maintenance. If you figure a minute per inspection point, it should have at least taken half an hr. I've showed up to furnaces that look flawless, and I still take them apart and clean them because that's what the homeowner paid me for. If there is even a hint of a cracked heat exchanger, get a second opinion. There are scams out there, and unfortunately a 20 minute inspection wouldn't reveal that. Have whomever is making the claim show you via camera or by physically removing the combustion chamber from the furnace and showing you. As weird as that sounds, I've removed heat exchangers out of furnaces just to prove that there was an issue. A cracked combustion chamber can be a serious issue, so the fact that he said it should be fine says either he doesn't know what he's doing or he's not being truthful, or both. It's not that cracked heat exchangers are leaking carbon monoxide, it's that they can. It's the potential that makes it dangerous. Hope this helps!


CM Heating performed an electric furnace Diagnostic - Upon investigation, I found that the sequencer has failed which is why all heat elements are not being activated (3 out of 5 work). This is the second replacement sequencer needed in less than 5 years of operation, the unit is an old model of air handler and only source of heat. Replacement of sequencer is needed, however, based on age and efficiency recommend upgrade of system.

As the largest heating company in the Northwest, Washington Energy Services has fixed thousands of heating systems. We service most major brands of heating equipment, including York, Bryant, Carrier, Lennox, Coleman and Rheem. Our NATE certified, factory trained service technicians are standing by for furnace service, and also heat pump and air conditioning repair. Home owners from Sea-Tac to Lynnwood trust Washington Energy Services for furnace service and repair. Schedule your service today!
All major furnace manufacturers strongly recommend an annual tune up by a qualified, insured, and trained technician staff. Failing to do so in many cases means voiding your manufacturer warranty, which could mean a total loss for your equipment if something goes wrong. In the grand scheme of things, the cost of an annual tune-up is well worth it as compared to the cost of replacing a furnace all together.
As a technical industry, the heating and cooling field is associated with annual advances. New energies make our industry an exciting place to work. Our team thrives on keeping up to date with all changes in the HVAC field. We are here to share our knowledge with each customer. When you are ready to update your HVAC system, we can help you select the ideal system for your home.
Our team is NATE-certified.  North American Technician Excellence represents the entire HVAC industry and is an independent, third-party, non-profit organization.  NATE-certified technicians are skilled professionals who have verified real working knowledge of HVAC systems through specialized exams.  Whether your heating or cooling system requires routine maintenance or complex repair, the NATE-certified team from Nerthling's Heating and Air Conditioning shows up on time, prepared to complete the job quickly and accurately, without unnecessary multiple house calls.  We work on all makes and models and offer affordable and convenient service plans to protect your equipment from wear and tear, and ensure like-new performance.

Heating Repair Company CO

×