Another energy savings tip, HVAC professionals say, is using a programmable thermostat. A programmable thermostat can save you up to 10 percent on energy bills, if you dial it down seven or eight degrees from the normal temperature setting — the U.S. Department of Energy recommends a setting of 68 degrees — for eight hours a day, whether it's during the work day or at night, according to DOE.
Ultimately, the cost to repair your furnace depends on a wide range of variables. From the brand of the units to the damaged or broken parts, you need a reliable and trusted professional who can evaluate the issue and recommend next steps. If you're unsure whether to repair or replace your furnace, or even where to begin, connect with a local furnace repair professional who can make sure that your home heats well both now and in the future.
Do you need expertise in HVAC? Roswell and Marietta residents who choose Moncrief Heating & Air Conditioning get the benefit of over 118 years of reputable experience in air conditioning and furnace repair, service and installation. Whether you have an emergency or need routine service, we are available 365 days a year. Call us today at 404-350-2300.

Zolie and Charely were very professional and on time.They gave us an estimate to replace our water heater and went over all our options.We opted to have them install a new water heater and get things up to code. Within three hours we had a new water heater installed. Zolie and Charley were efficient and pleasant to work with. We were pleased with the work that was completed!


Most manufacturers’ warranties call for annual equipment maintenance to stay valid, so missing your tune-ups can possibly result in losing your heating or AC system warranty, which can be major money if your equipment does ever stop working in the middle of a cold snap. Make sure you get all you can from your warranty by making sure it stays valid as long as possible with annual furnace system tune-ups from Service Experts.
You can usually slip the belt on the motor’s (smaller) pulley first and then start it on the blower pulley. Rotate the blower pulley by hand, holding the belt in place but keeping your fingers from getting caught between the belt and the pulley. The belt should slip right into place. If it seems to be too tight or difficult to set in place, it may be necessary to adjust the motor mount to provide more slack.

Furnace tune ups should take anywhere from 45 minutes to hour and a half, depending on what the technician has to deal with when he gets there. I was a heating and AC professional for over 10 years and I had tune ups that only took me 30 minutes, and others where it seemed like I had to practically disassemble the entire furnace, clean, then put back together. Every call is unique. However, it's important you trust your contractor. Your instincts are more accurate than you probably give yourself credit for. I don't remember a tune up ever going less than a 1/2 hr in my 10 years of experience. It just takes time to setup, take down, and perform the actual maintenance. If you figure a minute per inspection point, it should have at least taken half an hr. I've showed up to furnaces that look flawless, and I still take them apart and clean them because that's what the homeowner paid me for. If there is even a hint of a cracked heat exchanger, get a second opinion. There are scams out there, and unfortunately a 20 minute inspection wouldn't reveal that. Have whomever is making the claim show you via camera or by physically removing the combustion chamber from the furnace and showing you. As weird as that sounds, I've removed heat exchangers out of furnaces just to prove that there was an issue. A cracked combustion chamber can be a serious issue, so the fact that he said it should be fine says either he doesn't know what he's doing or he's not being truthful, or both. It's not that cracked heat exchangers are leaking carbon monoxide, it's that they can. It's the potential that makes it dangerous. Hope this helps!
If your home is not heated using forced air, chances are a boiler will make sure you stay warm during cold nights. A hot water system delivers hot water through a network of pipes that run to every room in your house. The heating effect gets maximized through radiators. The most common issues with hot water heating tend to be not be major, but small problems that add up over time. Mineral deposits within the water tank, a pilot light malfunction, or an issue with a radiator itself can require professional repair. On average, you will pay between $183 and $582 for these problems. The exact amount will depend on the exact problem, as described in our boiler repair cost guide.
Maryville, TN Appliance Repair Brookfield, WI Appliance Repair Appliance Repair Santa Cruz, CA Appliance Repair Riverside Appliance Repair Naples, FL 1500 S Willow St Appliance Repairs Appliance Repair in La Crosse Appliance Repair in Laredo 200 Westgate Dr Appliance Repairs 6929 Williams Rd Appliance Repairs Appliance Repair in Chesapeake Appliance Repair in Springfield, OH Appliance Repair in Whittier Appliance Repair in Massena Appliance Repair in Duluth Appliance Repair in Richardson Appliance Repair in Saint Joseph
If your furnace sputters to a halt during the evening or overnight in the middle of winter, you can bet that the indoor temperature will plummet by morning and everyone will be cold and uncomfortable. It isn’t as bad as outside because you have wind protection and residual heat, but no one in the house will be happy. The key to finding a quick solution to these kinds of scenarios is to align yourself with a reputable, reliable service provider before there is a problem. If you have a local expert in your corner, you can call as soon as something happens and your service disruption will be minimal.
When a furnace maintenance is performed a combustion analysis should be performed to identify any problems that couldn't be found by a visual inspection. You want to know what the Carbon monoxide level your furnace is producing as well as the oxygen/CO2 levels and stack temperate. The analyzer will also give you a calculated efficiency rating with the information the analyzer receives. You should have >100ppm of Carbon monoxide output during normal operation of your gas furnace. When you have higher numbers or CO numbers increasing during operation their is a problem with the furnace the technician should then find the cause of. This is just a brief explanation I'm trying to get across to those who get their furnace maintained and to those who don't! Check to see if anyone in the company has a NCI certification for carbon monoxide/combustion analysis.

Furnace Service Company

×