Your furnace's flame sensor is essentially a safety mechanism. As a thin metallic rod in front of the flame inside the unit, it's sole purpose is to confirm that your gas valves only open when a flame actually exists to burn that gas. When the flame sensor stop working, on the other hand, gas leaks can occur. To repair your furnace's flame sensor, expect to spend between $80 and $250. Even a full replacement of this part typically does not go above that range.
At Bob’s Heating & Air Conditioning, we believe that our customers deserve to live comfortably throughout the entire year. That is why we offer such a comprehensive selection of air conditioning, heating and water heater services in Kirkland, WA. When you work with us, you can rest assured that your furnace is installed properly, your AC maintenance is meticulous, and that your water heater repairs are top notch. Contact us today to learn more about the heating and cooling services we offer throughout Kirkland, WA.
Cleaning the debris that builds up on your filters will aid with the flow of air. When your air filter is clogged, your air handler must work harder to compensate for the blockage of air flow. In addition to driving up your utility bill, the reduced air flow through your heating and cooling system can cause your heat exchanger to overheat and shut off too quickly.    
After an HVAC professional services the furnace, there are a few steps homeowners can take to keep it running smoothly. Most importantly, perhaps, is changing the air filter regularly, at least every three months, according to Energy Star, which is a branch of the U.S. Environmental Protection Agency. A clogged air filter will restrict air flow, which can also negatively affect your health through exposure to environmental contaminates.

Your HVAC system is an important appliance with a limited lifetime. Depending on use, with regular maintenance you can expect your furnace and air conditioner to last between 8-18 years before you will need to replace the old one. However, poor maintenance is one of the primary reasons for early replacement HVAC systems ahead of end of average life expectancy. 

Put simply, any home that uses air pushed through ductwork for heating purposes takes advantage of forced air heating. In other words, this term refers not to your furnace, but to the delivery method of the heat throughout your home. Forced air heating is possible with electric or gas furnaces, or a heat pump. Any issues with this delivery system that aren't directly related to the furnace likely have to do with the duct work, which costs between $35 and $55 per linear square foot to repair, or the air handling unit.
For starters, once a year, vacuum out the area around the furnace’s blower. If possible, also slide out the fan unit, clean each fan blade with a toothbrush, and then vacuum with a brush attachment on a vacuum cleaner. While you’re at it, look for oil ports on the motor, normally located near the motor shaft. If the motor has these, apply two to three drops of non-detergent motor oil into each port (you may have to remove a cover plate to do this). Though most contemporary motors don’t require lubrication, do lubricate motors with oil ports once a year. For more about maintenance, see Maintenance Checklist for Central Heating Systems.
The professionals here at Brothers Plumbing, Heating and Electric are well trained, experienced and seasoned experts. We have been the go-to plumbing, electrical and HVAC company in the area for over 35 years and we always come highly recommended by our many satisfied customers. We offer a 100% satisfaction guarantee, have an A+ Rating with the BBB, won the Thornton “People’s Choice Award” for 2016, drug test and background check all of our employees, email you a picture of the technician who will be providing the service before arrival and call once the service is complete to ensure 100% satisfaction. So what are you waiting for? With our competitive pricing, trained and experienced technicians, and well-rounded list of home services, we’re clearly the company to trust. Get in touch with us here at Brothers Plumbing, Heating and Electric to schedule your needed service today!
Great article! I am having trouble identifying what to use for the aluminum or zinc strips to prevent organic growth and staining. How wide are the strips? Are they predrilled? I am starting to see black stains on the north facing asphalt shingles. Do you recommend treating that befor adding the metal strips? If so, 50/50 bleach and water or a commercial product?

Heating Repair Company

×