Specializing in Bryant brand heating and cooling products, we offer a broad selection of innovative, industry leading technology to improve the comfort, health, and efficiency of your home or office. Our technicians are certified and highly trained to provide residents in Thornton, CO & Westminster, CO with unmatched heating and air conditioning services, including installation, repair and maintenance. Plus, our team of plumbers offers a range of indoor and outdoor plumbing solutions, including repair and installation of faucets, fixtures, water heaters and toilets, frozen pipe prevention and repair, and natural gas line service. Give us a call and take advantage of our proven dedication and prompt response.
Furnace Repair Company
Advice you can count on – When you have an emergency, you are not always in the position of asking questions to determine if the repairs you are receiving are what you need. At Jennings, our NATE Certified technicians will walk you through the repairs and explain why you need them. You can trust that everyone on Jennings’ staff will give you honest advice.
Aurora residents are well aware that when the furnace goes out in their home, can be incredibly frustrating to get working again. At times, there are serious things that go wrong with a home that needs to get fixed very quickly. As far as the furnace goes, it needs to get repaired or fixed as soon as possible, which is why it’s good to know that our furnace repair company does furnace replacement in Aurora and also Aurora furnace repair, is prepared to help at any time. To learn more about our furnace and heating services, click HERE today!
Our technicians have many years of experience repairing furnaces and will make sure your home is back to keeping you warm and cozy in no time. From training and certifications to our reputation for completing the job right time and time again, you can be sure that B & B Heating & Cooling’s furnace repair technicians will have your problems taken care of and your furnace operating smoothly. Whether it’s emergency furnace repair or service you can schedule some time in advance, our team can provide you peace of mind, knowing that your furnace is in experienced hands. Need a furnace repair? When performing a repair, it's crucial to vet professional HVAC contractors.
Before performing DIY furnace maintenance, Richard makes sure to switch off the electrical power and the fuel supply. The distinctive red power switchplate can usually be found at the top of the cellar stairs or near the burner itself, while the fuel shutoff valve is near the oil tank or on the incoming gas pipe. Note the location of both in case of a future leak or fire.
What happens when you have an emergency? The first reaction of most people is to panic. When a furnace stops working, you need it fixed and fixed immediately—especially in the middle of a cold, Ohio winter. That need can make people feel as if they are at the mercy of the repair company. That is why it is so important to call a company you can trust and rely on—Jennings Heating and Cooling.
Modern high-efficiency furnaces not only provide superior heating, they save money on energy bills, last longer and generate less noise. The hands-on experience, technical expertise and dedication of the team from Choice Heating & Cooling ensures that your new equipment operates at peak performance, providing consistent enjoyment for years to come. To further protect your investment, Choice Heating & Cooling offers prompt repair and comprehensive maintenance, delivering consistent warmth at fair prices.
The cost to replace your gas furnace will vary based on the type and size of furnace you select, labor and installation costs, and any repairs your HVAC system may need. Nationally, average HVAC prices for a heating specialist range between $1,800 and $2,500. It’s important to select the right size gas furnace for your heating needs. A furnace that’s too small won’t heat your house properly, while a furnace that’s too large will run inefficiently, cycling on and off and likely breaking down sooner. HVAC specialists calculate your exact heat needs by measuring your home and incorporating variables such as the regional climate and your home’s level of insulation. Retail pricing for gas furnaces can range from $650 up to $3,000 and more. The higher the AFUE (annual fuel utilization efficiency) rating of the furnace, the more efficient it is at turning fuel into heat and the lower your carbon footprint and utility bill will be. HVAC installation costs are often based on an hourly rate and can range from under $50 to over $100 per hour, depending on the company and the furnace being installed. Higher-end furnaces cost more to install because they require added labor and expertise. For a typical installation, it might take two HVAC installation pros one day or less to remove your old furnace and replace it with a new one.
So the furnace went out (again). We’re probably not the people you want to be dialing, but in these circumstances, Service Experts Heating & Air Conditioning in North America should be your very first call. You don’t even have to worry how late (or early) it is – our NATE-certified technicians available at all hours, every day of the year. We’ll be there in a jiffy and get the job done fast – so you can get back to your routine and not have to even think about needing another furnace repair anytime soon.
When your gas furnace isn’t blowing hot air, the issue could be due to a faulty pilot light or broken ignitor. Remove the furnace cover panel and visually inspect whether you can see a flame from the pilot light. A natural gas furnace will be blue and yellow in color, and a propane furnace should have a bluish green flame with a yellow tip. If you can see a flame and it appears normal, the issue could be related to the furnace blower motor or other complex furnace parts. If the flame appears low or non-existent, it’s best to contact an experienced furnace repair company. Remember to never touch any open wires; contact a professional.
Furnace tune ups should take anywhere from 45 minutes to hour and a half, depending on what the technician has to deal with when he gets there. I was a heating and AC professional for over 10 years and I had tune ups that only took me 30 minutes, and others where it seemed like I had to practically disassemble the entire furnace, clean, then put back together. Every call is unique. However, it's important you trust your contractor. Your instincts are more accurate than you probably give yourself credit for. I don't remember a tune up ever going less than a 1/2 hr in my 10 years of experience. It just takes time to setup, take down, and perform the actual maintenance. If you figure a minute per inspection point, it should have at least taken half an hr. I've showed up to furnaces that look flawless, and I still take them apart and clean them because that's what the homeowner paid me for. If there is even a hint of a cracked heat exchanger, get a second opinion. There are scams out there, and unfortunately a 20 minute inspection wouldn't reveal that. Have whomever is making the claim show you via camera or by physically removing the combustion chamber from the furnace and showing you. As weird as that sounds, I've removed heat exchangers out of furnaces just to prove that there was an issue. A cracked combustion chamber can be a serious issue, so the fact that he said it should be fine says either he doesn't know what he's doing or he's not being truthful, or both. It's not that cracked heat exchangers are leaking carbon monoxide, it's that they can. It's the potential that makes it dangerous. Hope this helps!
An improperly maintained heating and air conditioning is an inefficient heating and air conditioning system. That’s why we provide appointments for annual inspections with our licensed technicians. It’s our goal to make sure that your home is as comfortable and energy-efficient as possible. For inspections, repairs, and service, contact BGE HOME for quality service.
The fully licensed and insured, NATE-certified team from Marky Mark's Heating, Cooling & Plumbing, LLC is always available when you experience a problem with any make, model, or style of HVAC or plumbing system. We offer 24/7 Emergency Repair in Thornton, CO & Westminster, CO and throughout the Northern Denver Metro area, handling residential and light commercial application, arriving promptly and prepared to complete the majority of issues in a single visit.
If your furnace’s motor runs but the blower doesn’t move air, the belt that connects the two probably has broken. Replacing it is an easy fix. First, turn off all power to the unit and turn off the gas at the gas valve that serves the furnace. Remove the door on the front of the furnace cabinet to give you access to the blower (it might be on a slide-out drawer.) Check the number stamped on the belt and get an exact replacement from a home center or heating supply outlet.
Even if your air conditioning unit is still working, depending on the type of system in your home today, you could recoup your investment in a new system in as little as three years. However, that doesn't mean that your system needs to be replaced. Furnaces, air conditioners, and other heating and cooling systems have made tremendous gains in efficiency over the past five years, so if you have an older unit, it is worth taking a look at whether or not a repair is the best investment.
An electric furnace provides warmth by moving air over and through a series of coils. Ductwork and vents then distribute that air to the individual rooms in your home. Repair costs will depend on both the brand and the exact nature of the problem, but tend to be lower than some of the options above. That's because the units are small, and issues tend to be contained within the heating elements themselves. Expect to spend less than $300 on your electric furnace repair, depending on the exact problem.
Here at Metro Heating and Cooling, we offer the best services for Pittsburgh furnace repair and air conditioner repair. All of our technicians are NATE certified, which means they have met the strictest standards and the highest level of training in the industry. When you hire a company with NATE certified technicians, you can be assured of excellence in the products and services you receive. Our team can help you with any issue you may be having with your heating or cooling systems and, walk you through options to help determine the best solution for your needs and budget. Contact Metro Heating and Cooling today!
Start with your utility company; they can help a great deal. Comparing previous bills isn't always a good measure, as the weather is never exactly the same month to month. Instead, if you take your energy bill and divide it by the square footage of livable space in your home, don't count areas like unfinished garages or basements -- you can calculate how much you are spending to heat or cool each square foot of your home. Your energy provider can tell you what the average cost per square foot is in your region for that same period of time so you can compare apples to apples.