I was disappointed with the pressure of a tub and shower that were plumbed with 1/2 supply lines (2nd floor). Could be low pressure from the street, but I want to replace with 5/8. Plus, I'd like to have 2 back to back showers, one inside and one outside. So, I had intended to bring a 1 supply to both, then branch up to valves and shower head with 5/8. Finally, I thought pressure from the street was typically 55 to 70 psi and I am concerned if pvc can take that.Any thoughts?
Advice you can count on – When you have an emergency, you are not always in the position of asking questions to determine if the repairs you are receiving are what you need. At Jennings, our NATE Certified technicians will walk you through the repairs and explain why you need them. You can trust that everyone on Jennings’ staff will give you honest advice.
At Bob’s Heating & Air Conditioning, we believe that our customers deserve to live comfortably throughout the entire year. That is why we offer such a comprehensive selection of air conditioning, heating and water heater services in Kirkland, WA. When you work with us, you can rest assured that your furnace is installed properly, your AC maintenance is meticulous, and that your water heater repairs are top notch. Contact us today to learn more about the heating and cooling services we offer throughout Kirkland, WA.
Furnace Service Company CO
To keep your furnace in good working order it’s important to have it regularly cleaned. The national average furnace cleaning cost ranges from $60 to $80, though prices can vary greatly based on where you live in the country and what your furnace maintenance includes. An HVAC company may have different rates for different levels of furnace maintenance. For example,one company may offer general furnace maintenance for $79 and advanced maintenance for $138. Another company may offer a 38-point maintenance check for $89 and a 64-point maintenance check for $178. According to Energy.gov, a standard furnace cleaning and maintenance visit can include:
Although San Antonio is known more for its heat than its cold, here at Will Fix It, we’ve helped thousands of Texans keep warm during our many cold snaps with a quick heating repair. We have professional HVAC technicians who have repaired and serviced all kinds of heating systems. Let one of our experienced technicians offer a reliable diagnosis of the issue and provide an upfront, written estimate that includes options and recommendations. No work is done until you approve.
Next check and clean the furnace’s flame sensor. The video below shows you how—note that this guy fixes it in about 5 minutes. We would probably use a little bit of emory paper, but he cleans the sensor with a 5-dollar bill. Another video further down the page under the discussion of “If your furnace keeps shutting off after about 5 minutes” shows the same project with a different brand of furnace.
This is probably the most common question we hear. To give an accurate price, we need to get a safety certified technician out to your home in a fully stocked truck to take a look at your particular situation. Our technician will give you a precise price with your options BEFORE any work begins. Each of our technicians are well trained, experienced, drug tested and background checked so that you can rest easy knowing your services will be performed in a timely and professional manner. If you need help paying for your services, we even offer financing with approved credit through Wells Fargo. Click here to learn more about our financing services.
You should never wait for your furnace to break down completely before scheduling professional furnace repair service in Kirkland, WA. The best way to handle any furnace repair needs is to contact a repairman at the first sign of trouble. If you notice a spike in heating costs, your furnace is not heating your home evenly, or it makes strange and unusual sounds, then it’s time to bring in a qualified Kirkland furnace repair technician.
Looking for local and trusted heater repair that is nearby? HVACs Today is here to help. Keeping your home or business heated is what we are great at. From installation to replacement and repairs, our technicians can complete your job quickly and correctly. Skilled contractors can solve your heater repair needs: no problem is too big or too small. Call us today to schedule your heating repair service.
There’s a common misconception that you can save money by shutting the vents (supply registers) in rooms that aren’t being utilized. Resist the urge to close too many, as doing so can actually increase the pressure in your furnace, making it work harder to heat your home. This can lead to failed blower motors, mold or mildew in your ductwork, damage to the compressor, a cracked heat exchanger, and other problems. What Does a Furnace Tune-Up Include?
BGE HOME HVAC repair technicians are thoroughly trained and certified to work on all major brands of heating and air conditioning equipment. When your system breaks down and needs a heating and air conditioning repair, you want to call someone you can trust. Need air conditioning service in the middle of the night? Emergency heating and cooling HVAC service is available 24 hours a day by calling 888-243-4663.
Air Conditioning and your heating source are intertwined. In the summer it’s the AC system you’re concerned with. In the winter it’s the furnace. Do your AC service annually, just like you maintain your furnace. Leaves and dirt and yard debris will get lodged in the air conditioning condenser unit, the part that sits outside. Cleaning this trash from your condenser will improve the efficiency of your HVAC system and help your air conditioner to last longer, avoid AC service and save you on your electric bill.
We don’t just repair and replace existing equipment, either. We also do upgrades. Summers get hot and winters get cold here in Kansas City, KS. If your water heater, furnace, or AC unit just isn’t cutting it, we can install a new one. We always offer the best price on new equipment, including easy financing options. Call us for a free estimate, and if you decide the price is right, we’ll send out one of our expert technicians to install your furnace, AC or water heater.
Natural gas furnaces operate similarly to the above, using a pilot light to ignite the burners and heat up the air. Also similar to propane gas, your average repair costs for a natural gas furnace will range anywhere from $125 for small repairs to $1,200 if you have to replace the entire heat exchanger. The difference between both options is not necessarily the actual furnace, but the type of gas used to burn through it and heat your home. As a result, the repair costs tend to be close to identical.
To keep your natural gas furnace operating efficiently, you should have at least an annual tune up. Natural gas furnace preventative maintenance will help avoid operating problems. When issues are addressed early on, it’s more likely that they can be resolved with minimal cost. Worn out parts and clogged filters that happen over time can lead to more significant equipment failures.
"Most people don't understand [and when they] put a new system in think, 'I’ve got a new system, so I won't have to maintain it,'" Conover said. "Well, there's nothing greater from the truth than that, because manufacturers require you to have regular maintenance and to have record of that. If you would ever have a warranty claim, that manufacturer has the ability to ask you for those service records. So not only does it make sense from a perspective of the longevity of it, but if you have a warranty, you want to make sure you keep it intact."
We came home to a gas leak and our CO detector going off last Thursday (was very cold out)! After contacting Natl Fuel we proceeded to call Nerthlings for help! They arrived quickly, found the problem & worked with us to install our new furnace the next day. They were great to deal with & a huge help with the bad weather we were having at the time!
Great article! I am having trouble identifying what to use for the aluminum or zinc strips to prevent organic growth and staining. How wide are the strips? Are they predrilled? I am starting to see black stains on the north facing asphalt shingles. Do you recommend treating that befor adding the metal strips? If so, 50/50 bleach and water or a commercial product?
When a furnace maintenance is performed a combustion analysis should be performed to identify any problems that couldn't be found by a visual inspection. You want to know what the Carbon monoxide level your furnace is producing as well as the oxygen/CO2 levels and stack temperate. The analyzer will also give you a calculated efficiency rating with the information the analyzer receives. You should have >100ppm of Carbon monoxide output during normal operation of your gas furnace. When you have higher numbers or CO numbers increasing during operation their is a problem with the furnace the technician should then find the cause of. This is just a brief explanation I'm trying to get across to those who get their furnace maintained and to those who don't! Check to see if anyone in the company has a NCI certification for carbon monoxide/combustion analysis.