Regarding your post, Every technician performs a maintenance differently. Today's modern furnaces really don't require as much maintenance as older style systems did. For instance: Older furnaces had drive belts, pulleys and motors with oil ports.Today's blowers are direct drive no belts, no pulleys, sealed bearing motors no oiling required. All of the new modern technology cuts the maintenance time in half if not more. Today's equipment has multiple safety's in place so that in case of a failure the system will shut down. non serviceable control boards or (Brains) monitor system functions. Unlike oil systems, the maintenance on a gas system can possibly be completed in less than half the time. I'd say 20 to 30 minutes is about right unless a service issue arises. In the 30 minute time span, the doors can be removed, system components can be visually inspected, the flame can be inspected and co test can be performed for spillage and vacuum of the combustion area can be performed if needed. The air filter should be checked and the humidifier can be activated. Remember that probing into a perfectly functioning system can be detrimental to its lifespan. My advice is change you air filter, keep the area around the equipment free of dust and try not to store in close proximity to the heating plant. Be sure you have an updated quality carbon monoxide detector in your home. Regarding the crack in your heat ex-changer, If the heat ex-changer had a crack in it, the system it should have been shut down right then and there. Be aware that Carbon monoxide may be entering your living space due to that crack. Have a knowledgeable company come back and do a CO test in your home at the supply vents and use a scope to check your heat ex-changer for cracks. I hope this helps you. Bottom line, you have to trust the company that you are using. If you feel uncertain about their capabilities, then more than likely, you instinct is correct. Good Luck to you.. Happy Holidays
Do not try to do DIY gas furnace maintenance or tune-ups yourself. In addition to being dangerous, this may also violate the manufacturer’s warranty. Let properly trained and experienced technical staff perform all gas furnace preventative maintenance. Regardless of your DIY talent, trying DIY furnace maintenance is fraught with hazards and risks to your heating system—and yourself.

Zolie and Charely were very professional and on time.They gave us an estimate to replace our water heater and went over all our options.We opted to have them install a new water heater and get things up to code. Within three hours we had a new water heater installed. Zolie and Charley were efficient and pleasant to work with. We were pleased with the work that was completed!
Aurora residents are well aware that when the furnace goes out in their home, can be incredibly frustrating to get working again. At times, there are serious things that go wrong with a home that needs to get fixed very quickly. As far as the furnace goes, it needs to get repaired or fixed as soon as possible, which is why it’s good to know that our furnace repair company does furnace replacement in Aurora and also Aurora furnace repair, is prepared to help at any time. To learn more about our furnace and heating services, click HERE today!
All major furnace manufacturers strongly recommend an annual tune up by a qualified, insured, and trained technician staff. Failing to do so in many cases means voiding your manufacturer warranty, which could mean a total loss for your equipment if something goes wrong. In the grand scheme of things, the cost of an annual tune-up is well worth it as compared to the cost of replacing a furnace all together.

If your furnace sputters to a halt during the evening or overnight in the middle of winter, you can bet that the indoor temperature will plummet by morning and everyone will be cold and uncomfortable. It isn’t as bad as outside because you have wind protection and residual heat, but no one in the house will be happy. The key to finding a quick solution to these kinds of scenarios is to align yourself with a reputable, reliable service provider before there is a problem. If you have a local expert in your corner, you can call as soon as something happens and your service disruption will be minimal.


At some point, your air conditioning system is no longer going to be worth the cost of repairs. It may also suffer irrevocable damages. Whatever your reasoning, it is necessary that you contact a highly skilled, extensively trained expert for professional air conditioning replacement in Kirkland, WA. Take no chances with the quality of your AC replacement.
The motor belt should be firm, giving no more than ½ inch when pressed. It should also be free of cracks and damage. To remove the belt, you will need a wrench and a replacement belt. Loosen, do not remove, the motor bolts. You only need them loose enough to move the motor and slacken the belt. Remove the belt and inspect it, replacing it with a new one if necessary. Belt: $4.00 to $6.00.
Given the broad price ranges above, it's easy to recognize that the cost of your furnace repair varies drastically based on which parts need attention. As a result, it makes sense to gain a better understanding of the parts that heat your home, and how much they cost to repair. Repairing or replacing your furnace’s blower motor can cost you anywhere between $150 and $450, depending on the extent of the damage. Heat exchanger repair costs can vary greatly, from as little as $100 for a simple fix to as much as $1,200 for a full replacement. Repairing a furnace igniter will only cost you $300 at most, while flame sensor repairs generally fall between $80 to $250. The average cost to repair your Thermostat will range from $108 to $282.

At B & B Heating & Cooling, heating and cooling isn’t solely our job, it’s our passion. We’re dedicated to providing you with high quality HVAC service in Florissant. No matter the size of the problem or time of day, you can rely on us to get the job done properly. After all, B & B Heating & Cooling has been working in the community since 1985, bringing comfort to our customers right when they need it.


It’s important to keep your furnace receives regular maintenance to ensure that it’s working properly and efficiently. Routine maintenance can also extend the life of your heating system by several years. Ask about our annual maintenance agreements that cover your plumbing, heating, and cooling systems and save you money. A furnace that has been neglected may be working too hard, which can result in inconsistent air temperatures in your Minneapolis area home. Learn more about the importance of routine maintenance on your HVAC system.
Although San Antonio is known more for its heat than its cold, here at Will Fix It, we’ve helped thousands of Texans keep warm during our many cold snaps with a quick heating repair. We have professional HVAC technicians who have repaired and serviced all kinds of heating systems. Let one of our experienced technicians offer a reliable diagnosis of the issue and provide an upfront, written estimate that includes options and recommendations. No work is done until you approve.

Though forced-air furnaces are normally quite reliable, they can break down. To avoid break downs, it pays to know how to take care of your furnace and fix it when something goes wrong. Inevitably, a furnace stops working when you need it most. Consequently, fixing becomes urgent very quickly. The following instructions will help. With a little do-it-yourself experience and the proper guidance, you can troubleshoot and repair a variety of furnace problems yourself.


Regarding your post, Every technician performs a maintenance differently. Today's modern furnaces really don't require as much maintenance as older style systems did. For instance: Older furnaces had drive belts, pulleys and motors with oil ports.Today's blowers are direct drive no belts, no pulleys, sealed bearing motors no oiling required. All of the new modern technology cuts the maintenance time in half if not more. Today's equipment has multiple safety's in place so that in case of a failure the system will shut down. non serviceable control boards or (Brains) monitor system functions. Unlike oil systems, the maintenance on a gas system can possibly be completed in less than half the time. I'd say 20 to 30 minutes is about right unless a service issue arises. In the 30 minute time span, the doors can be removed, system components can be visually inspected, the flame can be inspected and co test can be performed for spillage and vacuum of the combustion area can be performed if needed. The air filter should be checked and the humidifier can be activated. Remember that probing into a perfectly functioning system can be detrimental to its lifespan. My advice is change you air filter, keep the area around the equipment free of dust and try not to store in close proximity to the heating plant. Be sure you have an updated quality carbon monoxide detector in your home. Regarding the crack in your heat ex-changer, If the heat ex-changer had a crack in it, the system it should have been shut down right then and there. Be aware that Carbon monoxide may be entering your living space due to that crack. Have a knowledgeable company come back and do a CO test in your home at the supply vents and use a scope to check your heat ex-changer for cracks. I hope this helps you. Bottom line, you have to trust the company that you are using. If you feel uncertain about their capabilities, then more than likely, you instinct is correct. Good Luck to you.. Happy Holidays


Cleaning the debris that builds up on your filters will aid with the flow of air. When your air filter is clogged, your air handler must work harder to compensate for the blockage of air flow. In addition to driving up your utility bill, the reduced air flow through your heating and cooling system can cause your heat exchanger to overheat and shut off too quickly.    
×