The cost to replace your gas furnace will vary based on the type and size of furnace you select, labor and installation costs, and any repairs your HVAC system may need. Nationally, average HVAC prices for a heating specialist range between $1,800 and $2,500. It’s important to select the right size gas furnace for your heating needs. A furnace that’s too small won’t heat your house properly, while a furnace that’s too large will run inefficiently, cycling on and off and likely breaking down sooner. HVAC specialists calculate your exact heat needs by measuring your home and incorporating variables such as the regional climate and your home’s level of insulation. Retail pricing for gas furnaces can range from $650 up to $3,000 and more. The higher the AFUE (annual fuel utilization efficiency) rating of the furnace, the more efficient it is at turning fuel into heat and the lower your carbon footprint and utility bill will be. HVAC installation costs are often based on an hourly rate and can range from under $50 to over $100 per hour, depending on the company and the furnace being installed. Higher-end furnaces cost more to install because they require added labor and expertise. For a typical installation, it might take two HVAC installation pros one day or less to remove your old furnace and replace it with a new one.
CM Heating performed an electric furnace Diagnostic - Upon investigation, I found that the sequencer has failed which is why all heat elements are not being activated (3 out of 5 work). This is the second replacement sequencer needed in less than 5 years of operation, the unit is an old model of air handler and only source of heat. Replacement of sequencer is needed, however, based on age and efficiency recommend upgrade of system.
Your furnace's flame sensor is essentially a safety mechanism. As a thin metallic rod in front of the flame inside the unit, it's sole purpose is to confirm that your gas valves only open when a flame actually exists to burn that gas. When the flame sensor stop working, on the other hand, gas leaks can occur. To repair your furnace's flame sensor, expect to spend between $80 and $250. Even a full replacement of this part typically does not go above that range.

In a lot of homes, in Chicago Illinois, the initial HVAC installation was banged together to get it done. We’ve found big errors in heat system installations, like heat registers that aren’t hooked up and ducts that are open and pumping heat into your crawlspace or attic, or thermostats installed in the wrong place. Our Heating system technicians can survey your HVAC system and suggest improvements that will improve your comfort and save you wasted fuel bills.
We install heating equipment from Lennox and can repair all major brands, including Carrier, Trane, York, Bryant, Rheem, and many more. We proudly offer same day service and next day installations. Dealing with a heating emergency? We've got you covered! Our team is prepared to assist you 24 hours a day, 7 days a week to ensure that your home remains comfortable and safe for you and your family members.

More often than not it’s because we’re afraid of high costs of service and finding the right company we can trust. When you choose Signature Heating, Cooling & Plumbing, there’s no need to worry. Rest assured our qualified and trained technicians can handle any type of service repair to maintain a quality of comfort your family is used to. We schedule your appointments with a date and time that can fit with your scheduling needs. We offer high-quality services at fair prices, giving you the best value for your money.
Here at Metro Heating and Cooling, we offer the best services for Pittsburgh furnace repair and air conditioner repair. All of our technicians are NATE certified, which means they have met the strictest standards and the highest level of training in the industry. When you hire a company with NATE certified technicians, you can be assured of excellence in the products and services you receive. Our team can help you with any issue you may be having with your heating or cooling systems and, walk you through options to help determine the best solution for your needs and budget. Contact Metro Heating and Cooling today!
Great article! I am having trouble identifying what to use for the aluminum or zinc strips to prevent organic growth and staining. How wide are the strips? Are they predrilled? I am starting to see black stains on the north facing asphalt shingles. Do you recommend treating that befor adding the metal strips? If so, 50/50 bleach and water or a commercial product?

Heating Repair Company

×