The fully licensed and insured, NATE-certified team from Marky Mark's Heating, Cooling & Plumbing, LLC is always available when you experience a problem with any make, model, or style of HVAC or plumbing system.  We offer 24/7 Emergency Repair in Thornton, CO & Westminster, CO and throughout the Northern Denver Metro area, handling residential and light commercial application, arriving promptly and prepared to complete the majority of issues in a single visit.


*Residential Service call's subject to $119.00 travel and diagnostic fee, Commercial Service call's subject to a $149.00 travel and diagnostic fee. Once diagnosed, necessary repairs will be quoted in accordance with standard flat rate repair price. Repair and quoted repair price may be accepted or declined by the customer at that time. Travel and Diagnostic fee will still apply in case customer declines repair. All calls are C.O.D. Overtime rates for Residential Service are $169.00, overtime rates for Commercial services are $179.00.  These rates are for services performed after normal business hours Monday through Friday 8am-4:30pm.

The installation and maintenance specialists from Nerthling's Heating and Air Conditioning are accredited by the manufacturer, having been extensively trained to correctly size and install ductless systems.  We are uniquely qualified to recommend, design, and service state-of-the-art systems.  Through knowledgeable and accurate workmanship, you’re ensured the highest level of rewards from your ductless system.
The cost to replace your entire unit is around $4,000. That expense can range from $2,500 to $5,900, depending on the type and brand of furnace you choose. Brands particularly have an impact on that price. A Goodman electric furnace, will only cost about $2,100 for the unit and labor. On the other hand, a Trane oil furnace may cost up to $9,000 all things considered. Our Furnace Installation Cost Guide can give you a better idea on both the general cost and the differences for brands like Amana, Bryant, Coleman, and others. The brand also plays into the repair cost for your furnace. Especially the prices of individual parts can change; a York heat exchanger, for example, can cost up to $1,900, while the same component from Heil will cost as little as $400.
Advice you can count on – When you have an emergency, you are not always in the position of asking questions to determine if the repairs you are receiving are what you need. At Jennings, our NATE Certified technicians will walk you through the repairs and explain why you need them. You can trust that everyone on Jennings’ staff will give you honest advice.
Vredevoogd Heating & Cooling is Michigan’s top Heating & Air – Furnace Repair & Replacement – Air Conditioning Repair and installation service. With decades of experience and expertise, Vredevoogd Heating & Cooling remains committed to offering affordable 24/7 service. Our skilled heating and cooling specialists are certified and background checked. Our team is here when you need us to meet all your heating and cooling needs.
Among the leading ways to prevent a breakdown and make sure it runs like a lean machine is with yearly scheduled tune-ups on your furnace. Just like any mechanical equipment, the useful life of a furnace will be enhanced with preventive maintenance, by ensuring that all the elements of the unit are running efficiently. In addition, regular cleanings can help pinpoint concerns before they become big problems and you end up paying emergency rates on a cold winter night. Plus, because furnaces burn fuel to make it hot, it’s important to inspect all the various pieces to ensure there aren’t any ruptures or leaks that could impact the safety of your family. Taking the time to schedule a tune-up, even when it’s not making that odd rattling noise you’ve been ignoring, will save you time, stress, and money throughout the heating season.
High-efficiency condensing furnaces (90% AFUE and above) are a bit more complex than conventional furnaces. The main differences between a conventional and condensing furnace are the heat exchanger technology used to extract heat from the combustion process and the method used to exhaust the combustion gases. In these ways, the furnaces are very different. The condensing furnace does not have a significantly more efficient combustion process than does a conventional furnace; both use gas burners with electronic ignition. The difference lies in that the condensing furnace has a more efficient heat extraction process after combustion.
Most manufacturers’ warranties call for annual equipment maintenance to stay valid, so missing your tune-ups can possibly result in losing your heating or AC system warranty, which can be major money if your equipment does ever stop working in the middle of a cold snap. Make sure you get all you can from your warranty by making sure it stays valid as long as possible with annual furnace system tune-ups from Service Experts.
CM Heating performed a Gas Furnace Diagnostic. Customer wanted his echo bee thermastat installed that he had bought himself. Furnace was working fine just wanted his thermastat installed. He thought that the $99 service fee was going to cover that but explained to him what the service fee was for, and explained that there is a additional install fee for the stat. Customer didn’t want to pay the additional fee so I called the office had them listen to the call to make sure we explained to the customer correctly and to see how they would like me to proceed. So I quoted the customer the fee to install the thermostat but he didn’t want us to install it so I left.
You can usually slip the belt on the motor’s (smaller) pulley first and then start it on the blower pulley. Rotate the blower pulley by hand, holding the belt in place but keeping your fingers from getting caught between the belt and the pulley. The belt should slip right into place. If it seems to be too tight or difficult to set in place, it may be necessary to adjust the motor mount to provide more slack.
Inspect your furnace thermostat by first making sure that it’s turned on. Also, ensure that the thermostat switch is turned to “heat” and not “cool”. If your furnace will still not start with the thermostat on, try adjusting the temperature settings to a few degrees higher. Inspect any visible wires for breaks or splits, and make sure your thermostat batteries are not dead. Do not touch any open wires; contact a professional.
We asked This Old House plumbing and heating expert Richard Trethewey to show us the proper steps that a service professional would follow for an oil-burning forced-air furnace; the basics on a gas system are similar. In both, fuel is mixed with air and ignited, heating a sealed chamber. Fresh, filtered air then blows across the outside of the hot chamber and into the heating ducts. (Homes with radiators have boilers instead of furnaces. These heat water instead of air, but the annual checkup is similar.) In all, the dangerous exhaust from the combustion chamber is vented out a flue or chimney.
Whether you are looking for gas furnace service or repair, quality installation of a furnace, heat pump or air conditioner, mini split ductless heat pumps, endless hot water from tankless water heaters, better air quality in your home or just a filter change or duct cleaning, Greenwood Heating is your best choice of Seattle heating contractors and cooling specialists.
At some point, your air conditioning system is no longer going to be worth the cost of repairs. It may also suffer irrevocable damages. Whatever your reasoning, it is necessary that you contact a highly skilled, extensively trained expert for professional air conditioning replacement in Kirkland, WA. Take no chances with the quality of your AC replacement.
For almost 30 years, Horizon Services has been providing top-quality heating services for homeowners throughout Delaware, Southern New Jersey, Southeastern Pennsylvania, and Northeastern Maryland. Whether you need furnace repair, heat pump replacement, new system installation, or comprehensive maintenance for your home's heating system, you can rely on our skilled team to get the job done quickly and efficiently. Our technicians undergo some of the most rigorous technical training in the industry, including 150 mandatory hours of technical and customer service training every year, in order to equip them with the skills, tools, and experience to handle any heating need you may have. No matter the issue you're currently dealing with, we can quickly and correctly diagnose the source of the problem and get right to work resolving the matter at hand.

When a furnace maintenance is performed a combustion analysis should be performed to identify any problems that couldn't be found by a visual inspection. You want to know what the Carbon monoxide level your furnace is producing as well as the oxygen/CO2 levels and stack temperate. The analyzer will also give you a calculated efficiency rating with the information the analyzer receives. You should have >100ppm of Carbon monoxide output during normal operation of your gas furnace. When you have higher numbers or CO numbers increasing during operation their is a problem with the furnace the technician should then find the cause of. This is just a brief explanation I'm trying to get across to those who get their furnace maintained and to those who don't! Check to see if anyone in the company has a NCI certification for carbon monoxide/combustion analysis.

Furnace Service Company

×