When it comes to furnace repair, Roswell and area residents can rely on us for fast and efficient repairs. Moncrief has continued to be a consistent provider of heating and cooling services in the Roswell and Marietta. We have worked hard to gain your respect by providing quality services and products, and delivering on our promise of total comfort for your home and family while providing energy and cost savings.
"Jorge Mondragon was very prompt and did an excellent job replacing my old heater furnace with a newer one. He explained me very well the details and specifics about why I would need a 3.5 ton furnace with the specific BTU given the square footage of my house. I would highly recommend him as he is a sound professional and very prompt in his service."
The oil filter (found in oil-powered systems only) prevents small impurities from clogging the oil-burner nozzle, which could result in a misfire that shuts down the system. Richard first closes the oil valve, then removes the old filter and replaces it, setting aside the dirty filter to be disposed of according to local hazardous-waste regulations.
An annual inspection of your unit can ensure that the various potential problems mentioned above are detected early, and before they require complete replacement. During this inspection, for instance, a professional might find small cracks in your heat exchanger or a faulty seal in your blower motor. Some manufacturer's warranties even require these annual inspections to maintain validity. Typically, your furnace inspection will cost between $80 and $150 depending on the area in which you live and the professional you work with.

If you pull out your home’s air filter, hold it up to a light. If you can’t see light coming through it, it’s most likely been a while since your last heating service, and likely time to get a new one. If it’s a simple disposable air filter, just replace it with a like-size new one. It’s also a good idea to write down the date you installed the new filter, so you know how old it is next time it needs to be replaced. Check the filter packaging to see how long the new air filter is supposed to be used.


Next check and clean the furnace’s flame sensor. The video below shows you how—note that this guy fixes it in about 5 minutes. We would probably use a little bit of emory paper, but he cleans the sensor with a 5-dollar bill. Another video further down the page under the discussion of “If your furnace keeps shutting off after about 5 minutes” shows the same project with a different brand of furnace.
With our furnace service, your burners will be pulled and cleaned. To ensure the best possible efficiency, we can adjust your heat-off delay. You can also expect a combustion analysis performed by a professionally certified HVAC technician. With a proper combustion analysis, we’ll be able to tell you if your furnace is operating at maximum efficiency and keep you safe.

When a furnace maintenance is performed a combustion analysis should be performed to identify any problems that couldn't be found by a visual inspection. You want to know what the Carbon monoxide level your furnace is producing as well as the oxygen/CO2 levels and stack temperate. The analyzer will also give you a calculated efficiency rating with the information the analyzer receives. You should have >100ppm of Carbon monoxide output during normal operation of your gas furnace. When you have higher numbers or CO numbers increasing during operation their is a problem with the furnace the technician should then find the cause of. This is just a brief explanation I'm trying to get across to those who get their furnace maintained and to those who don't! Check to see if anyone in the company has a NCI certification for carbon monoxide/combustion analysis.
Air Conditioning Your home's air conditioner is an essential part of your overall indoor comfort. A properly working system can mean the difference between a cool, comfortable summer and a hot, miserable few months. If you're currently dealing with a broken air conditioner, an inefficient system, or you would like to schedule a routine, pre-season tune-up, Horizon Services is here to help!

When you change the temperature on your thermostat, or the temperature in your home drops, a signal lets the furnace's igniter know that it's time to turn on. Igniters exist in both hot water boilers and forced air furnaces, replacing pilot lights as the switch your unit needs to kick on. Naturally, this is a core part in making sure it works reliably. When it stops working, your unit will not longer know when to actually heat your home. Fortunately, furnace igniter repair doesn't tend to be a major budget problem, and costs less than $300 on average.
If you need a furnace repaired or an air conditioner serviced, we'll send a local technician out to diagnose the specific problem and recommend solutions for you and your family. There will be a diagnostic fee for the visit, and any specific repairs will be an additional charge. If replacing your system is the best solution, the fee for the diagnosis will be credited toward the purchase and install of a new system.
“The manufacturers that built them all agree on this; you should get it serviced once [a year] for heating and once for cooling," says Paul Mills, owner of Air Experts Heating & Cooling in Raleigh, North Carolina. "Tuning it up and checking it out is definitely recommended. Much like a car, if you ignore it, a lot more things break. You [will] extend the life of it and help prevent major breakdowns.”
No one wants to be stuck in the dead of summer with a broken air conditioner, or in the cold of winter with a broken furnace or boiler. That’s why we’re available any time of day to make your emergency heating and air conditioning repair and get your system up and running as quickly as possible. We’ll show up on time, in uniform and ready to make your HVAC repair right the first time.
When a furnace maintenance is performed a combustion analysis should be performed to identify any problems that couldn't be found by a visual inspection. You want to know what the Carbon monoxide level your furnace is producing as well as the oxygen/CO2 levels and stack temperate. The analyzer will also give you a calculated efficiency rating with the information the analyzer receives. You should have >100ppm of Carbon monoxide output during normal operation of your gas furnace. When you have higher numbers or CO numbers increasing during operation their is a problem with the furnace the technician should then find the cause of. This is just a brief explanation I'm trying to get across to those who get their furnace maintained and to those who don't! Check to see if anyone in the company has a NCI certification for carbon monoxide/combustion analysis.
Turn off the gas supply valve, typically located by your gas meter on the gas inlet pipe. Turn off the gas by rotating the valve one quarter turn with an adjustable wrench. When the gas is off,  the valve’s oblong stem points perpendicular to the inlet pipe. Then call your gas utility or the fire department from a remote location. Do not return to your home until you know it is safe.
When the time comes to schedule furnace repairs, you want a team you can trust. Keeping your home warm and comfortable is important for you and your family, which is why you should rely on the highly-trained team of technicians at Horizon Services. Our techs undergo at least 150 hours of technical training every year and are up-to-date on the latest, most advanced techniques in the trade. We also background-check all of our employees to ensure your complete comfort and safety. When you call on us for furnace repair, we will arrive on-time and on schedule, ready to resolve the issue as quickly as possible.

If your furnace needs to be repaired, you’ll want to find a qualified heating, ventilating and air conditioning (HVAC) repair technician. Each state has its own licensing requirements; some require all HVAC technicians to have an HVAC license, while others only require someone operating an HVAC service and installation company with employees to hold a contractor’s license. For example, in Alabama, the Alabama Board of Heating Air Conditioning, and Refrigeration Contractors regulates licensing, while in Kansas there is no state regulatory body and HVAC licensing can vary by region. For simple furnace repairs like changing out a filter, a trusted handyman can probably handle the job, but a trained professional should be hired for tasks like replacing a gas valve, installing a new inducer fan motor or other critical furnace repair jobs that involve dealing with gas leaks or other dangerous conditions. For more, check out our tips for smart hiring on Thumbtack.
×