As touched on by their name, heat pumps function by transferring heat energy indoors during the winter and outdoors from your home during the summer. They're often attached to air conditioning units, using the surrounding air to transfer energy. However, geothermal heat pumps and water source heat pumps are also available. The cost to repair a heat pump, again, depends on the specific problem. Replacing a faulty thermostat may cost up to $300 including labor, while a worn or damaged defrost control board can set you back up to $600. For more details on your potential repair costs using this heating source, visit our heat pump repair cost guide.
Natural gas furnaces operate similarly to the above, using a pilot light to ignite the burners and heat up the air. Also similar to propane gas, your average repair costs for a natural gas furnace will range anywhere from $125 for small repairs to $1,200 if you have to replace the entire heat exchanger. The difference between both options is not necessarily the actual furnace, but the type of gas used to burn through it and heat your home. As a result, the repair costs tend to be close to identical.
We provide superior heating and cooling service and repair as well as HVAC system maintenance, repair and duct cleaning services. For over 20 years, Ballard Natural Gas Service has provided the highest quality services for your home. You can take comfort in knowing that we will treat your air conditioner, furnace, water heater, ducts or gas fireplace the same way we would treat our own, with the best care and highest quality professionalism. We treat you like family.
As a family-owned business, we take care of our customers with a comprehensive list of services, including heating and cooling installation, maintenance and repair, boiler installation and service, hot water heater service and geothermal systems.  We protect your best interests and strive to eliminate inconvenience through emergency service, free estimates, flexible financing, and 10 year parts & labor warranty included on new furnace installations.  Call Choice Heating & Cooling for your home comfort needs and expect more.  From your initial inquiry to the completion of the job, our goal is to exceed your expectations in every service we provide.
Inspect your furnace thermostat by first making sure that it’s turned on. Also, ensure that the thermostat switch is turned to “heat” and not “cool”. If your furnace will still not start with the thermostat on, try adjusting the temperature settings to a few degrees higher. Inspect any visible wires for breaks or splits, and make sure your thermostat batteries are not dead. Do not touch any open wires; contact a professional.

When your heating and cooling system stops working, you need the help of a reliable, experienced, local service professional that can diagnose the problem and repair your air conditioner or furnace at a fair price. You can count on The Home Depot's licensed and insured heating and cooling professionals for all your heaters, air conditioning units, and any ventilation needs.

Whether you are looking for gas furnace service or repair, quality installation of a furnace, heat pump or air conditioner, mini split ductless heat pumps, endless hot water from tankless water heaters, better air quality in your home or just a filter change or duct cleaning, Greenwood Heating is your best choice of Seattle heating contractors and cooling specialists.
We will work with you every step of the way to ensure that you get a consistent, reliable and effective performance from your heating system. From heating installation and replacement to routine maintenance and unexpected heating repairs, our Kirkland, WA heating technicians do it all. When it comes to heating system service in Kirkland, WA, there is no time to waste. Contact us today for more information.

When your furnace filter becomes dirty, dusty and clogged, you can expect some negative effects on your furnace efficiency and your indoor air quality. The forced air is supposed to get blown through the filter and the filter is supposed to trap any particles so they don’t end up in your air ducts and throughout the house. When the filter has trapped too many particles and it is clogged up, the air keeps blowing, but some of those trapped particles will end up in the system and your living space. Another effect is that the furnace has to work harder to get the same amount of air through that dirty filter, so your heating bills may go up.
Vredevoogd Heating & Cooling stands behind its services and products with the strongest guarantees you’ll find anywhere. When you invite us into your home to service or install your HVAC system or do Furnace Repair work in Grand Rapids and beyond, we perform our job with an outstanding level of care and efficiency. Having served Michigan for 54 years, we never rest on our laurels. To remain the best, we intend to give our best every time, every job.
We asked This Old House plumbing and heating expert Richard Trethewey to show us the proper steps that a service professional would follow for an oil-burning forced-air furnace; the basics on a gas system are similar. In both, fuel is mixed with air and ignited, heating a sealed chamber. Fresh, filtered air then blows across the outside of the hot chamber and into the heating ducts. (Homes with radiators have boilers instead of furnaces. These heat water instead of air, but the annual checkup is similar.) In all, the dangerous exhaust from the combustion chamber is vented out a flue or chimney.

With our furnace service, your burners will be pulled and cleaned. To ensure the best possible efficiency, we can adjust your heat-off delay. You can also expect a combustion analysis performed by a professionally certified HVAC technician. With a proper combustion analysis, we’ll be able to tell you if your furnace is operating at maximum efficiency and keep you safe.


On average, furnace repair costs $287 nationally, with some homeowners spending as little as $60 while others paying $900 for furnace maintenance. Repairs to an electric furnace can run you $300 or less, while gas furnace repairs can be more complex and range from $375 to $1,200, depending on the what needs service. Most homeowners spend between $131 and $453 to fix their furnace. Here is what you need to know, along with the various factors that could affect the price of your furnace repair.

If you have a heating or cooling emergency, call Vredevoogd Heating & Cooling Grand Rapids MI, Furnace Repair Lansing, Furnace Repair Kalamazoo and more at 616-828-5411. When you call you speak directly with one of our service representatives about the problem you are experiencing and schedule a service appointment. Naturally, we prioritize emergencies so you can count on us when your heating or cooling systems fail. After regular business hours, you can reach our customer service staff who will report your problem to on-call technicians. You can expect to hear back from a certified tech within 15 minutes of your call. Your heating and cooling emergency is important to us. We will visit your home ASAP to provide you with the superior service you’d expect from a Furnace Repair, Air Conditioning, AC Repair & HVAC leader like Vredevoogd Heating & Cooling Grand Rapids, AC Repair Lansing, AC Repair Kalamazoo.
When it comes to heater repair in Denver, a properly serviced system means significant savings for the homeowner. When a Denver heating technician inspects your system before the winter sets in, the first thing they will check is the condition of the air filters. These filters are important, because they are responsible for removing contaminants, allergens, and dust particles from the air every time the system is turned on. When the filters are clogged, expect more particles to easily pass through right into the air you breathe inside the home. The Denver heating experts will inspect and replace any filters that are no longer effective.

Metro Heating and Cooling has been providing superior services for heating and cooling Pittsburghresidents have relied on since 1957. We are a Carrier Factory Authorized Dealer, which means we have met the strictest standards in the heating and cooling industry, and we offer the finest products available. Our technicians are NATE certified, so when you choose us for heating and cooling services, you can be assured that you are receiving exceptional care. Regardless of your HVAC needs, we have the solution, ranging from installations of AC units and furnaces, to minimal repairs and maintenance services. Beyond having comfortable air, we want our customers to have healthy air in their homes and businesses. We offer indoor air quality products and services so you know you are breathing the cleanest air possible. Contact us today to learn more about our heating and cooling services.

As a Carrier Factory Authorized Dealer, M and M, Heating & Cooling, Plumbing & Electrical is qualified to properly size and install the most technologically advanced and well-regarded heating, cooling, and air quality products on the market today. Our team is NATE-certified, factory trained, EPA certified, and regularly updated, ensuring the right solution to any challenge.

I was disappointed with the pressure of a tub and shower that were plumbed with 1/2 supply lines (2nd floor). Could be low pressure from the street, but I want to replace with 5/8. Plus, I'd like to have 2 back to back showers, one inside and one outside. So, I had intended to bring a 1 supply to both, then branch up to valves and shower head with 5/8. Finally, I thought pressure from the street was typically 55 to 70 psi and I am concerned if pvc can take that.Any thoughts?


Turn off the gas supply valve, typically located by your gas meter on the gas inlet pipe. Turn off the gas by rotating the valve one quarter turn with an adjustable wrench. When the gas is off,  the valve’s oblong stem points perpendicular to the inlet pipe. Then call your gas utility or the fire department from a remote location. Do not return to your home until you know it is safe.
High-efficiency condensing furnaces (90% AFUE and above) are a bit more complex than conventional furnaces. The main differences between a conventional and condensing furnace are the heat exchanger technology used to extract heat from the combustion process and the method used to exhaust the combustion gases. In these ways, the furnaces are very different. The condensing furnace does not have a significantly more efficient combustion process than does a conventional furnace; both use gas burners with electronic ignition. The difference lies in that the condensing furnace has a more efficient heat extraction process after combustion.
×