This job involves removing the access panel, loosening a couple of bolts that hold the blower motor at the proper tension, and adjusting its distance or realigning the belt. In many cases, it’s a good idea to remove the belt and buy a replacement at a home center. Last, when reinstalling the belt, be careful not to over-tighten it; this can wear out the motor bearings.

Do not try to do DIY gas furnace maintenance or tune-ups yourself. In addition to being dangerous, this may also violate the manufacturer’s warranty. Let properly trained and experienced technical staff perform all gas furnace preventative maintenance. Regardless of your DIY talent, trying DIY furnace maintenance is fraught with hazards and risks to your heating system—and yourself.


For starters, once a year, vacuum out the area around the furnace’s blower. If possible, also slide out the fan unit, clean each fan blade with a toothbrush, and then vacuum with a brush attachment on a vacuum cleaner. While you’re at it, look for oil ports on the motor, normally located near the motor shaft. If the motor has these, apply two to three drops of non-detergent motor oil into each port (you may have to remove a cover plate to do this). Though most contemporary motors don’t require lubrication, do lubricate motors with oil ports once a year. For more about maintenance, see Maintenance Checklist for Central Heating Systems.
When your heating and cooling system stops working, you need the help of a reliable, experienced, local service professional that can diagnose the problem and repair your air conditioner or furnace at a fair price. You can count on The Home Depot's licensed and insured heating and cooling professionals for all your heaters, air conditioning units, and any ventilation needs.
Attic Fan Installation Bathroom Fan Repair Ceiling Fan Installation Ceiling Fan Repair Electric Wall Heater Installation Electrical Panel Installation Electrical Panel Repair Electrical Panel Upgrade Electrical Wiring Installation Electrical Wiring Upgrade Exhaust Fan Installation Holiday Lighting Installation LED Interior Light Conversion Light Fixture Installation Light Fixture Repair Light Fixture Replacement Light Switch Installation Outlet Installation Outlet Repair Spa Wiring Installation
High-efficiency condensing furnaces (90% AFUE and above) are a bit more complex than conventional furnaces. The main differences between a conventional and condensing furnace are the heat exchanger technology used to extract heat from the combustion process and the method used to exhaust the combustion gases. In these ways, the furnaces are very different. The condensing furnace does not have a significantly more efficient combustion process than does a conventional furnace; both use gas burners with electronic ignition. The difference lies in that the condensing furnace has a more efficient heat extraction process after combustion.
As the largest heating company in the Northwest, Washington Energy Services has fixed thousands of heating systems. We service most major brands of heating equipment, including York, Bryant, Carrier, Lennox, Coleman and Rheem. Our NATE certified, factory trained service technicians are standing by for furnace service, and also heat pump and air conditioning repair. Home owners from Sea-Tac to Lynnwood trust Washington Energy Services for furnace service and repair. Schedule your service today!
As a Carrier dealer, with a wide variety of products to choose from, we can keep your family healthy and feeling comfortable all year long. We carry a complete line of indoor comfort equipment with innovations that raise the standards of comfort and reliability, including air conditioners, heat pumps, gas furnaces, programmable thermostats, humidifiers, ductless split systems, air cleaners, ultra violet lights, ventilators and zoning products. Let the experts at A. Johnson Heating & Air help you customize a solution that's right for you.
Attic Fan Installation Bathroom Fan Repair Ceiling Fan Installation Ceiling Fan Repair Electric Wall Heater Installation Electrical Panel Installation Electrical Panel Repair Electrical Panel Upgrade Electrical Wiring Installation Electrical Wiring Upgrade Exhaust Fan Installation Holiday Lighting Installation LED Interior Light Conversion Light Fixture Installation Light Fixture Repair Light Fixture Replacement Light Switch Installation Outlet Installation Outlet Repair Spa Wiring Installation
Furnaces and thermostats are not mix-and-match appliances. Using the wrong type of thermostat with a furnace will cause operating problems and can be dangerous. Although thermostats look similar, they are designed very differently. There are numerous types of heating systems and thermostat systems and they need to be coordinated for safe and proper operation. There are three types of thermostat systems used today: millivoltage, low voltage, and line voltage.​
Aurora residents are well aware that when the furnace goes out in their home, can be incredibly frustrating to get working again. At times, there are serious things that go wrong with a home that needs to get fixed very quickly. As far as the furnace goes, it needs to get repaired or fixed as soon as possible, which is why it’s good to know that our furnace repair company does furnace replacement in Aurora and also Aurora furnace repair, is prepared to help at any time. To learn more about our furnace and heating services, click HERE today!
The cost to replace your gas furnace will vary based on the type and size of furnace you select, labor and installation costs, and any repairs your HVAC system may need. Nationally, average HVAC prices for a heating specialist range between $1,800 and $2,500. It’s important to select the right size gas furnace for your heating needs. A furnace that’s too small won’t heat your house properly, while a furnace that’s too large will run inefficiently, cycling on and off and likely breaking down sooner. HVAC specialists calculate your exact heat needs by measuring your home and incorporating variables such as the regional climate and your home’s level of insulation. Retail pricing for gas furnaces can range from $650 up to $3,000 and more. The higher the AFUE (annual fuel utilization efficiency) rating of the furnace, the more efficient it is at turning fuel into heat and the lower your carbon footprint and utility bill will be. HVAC installation costs are often based on an hourly rate and can range from under $50 to over $100 per hour, depending on the company and the furnace being installed. Higher-end furnaces cost more to install because they require added labor and expertise. For a typical installation, it might take two HVAC installation pros one day or less to remove your old furnace and replace it with a new one.
When your furnace isn’t regularly serviced it can operate less efficiently. This increases your energy bills and also prevents your furnace from keeping your home as warm as you like. Keep your furnace properly maintained with regular service. The national average furnace service cost is between $60 and $80. Companies may offer tuneup specials that cover all the necessary testing, tightening, measuring and cleaning to keep your equipment running at top efficiency. If you have a newer system, furnace service costs may be covered by your warranty. Outside of warranty, a basic tuneup might start at $58 and a more advanced maintenance cleaning could be over $120. Here are some signs your furnace may need service:
Furnace tune ups should take anywhere from 45 minutes to hour and a half, depending on what the technician has to deal with when he gets there. I was a heating and AC professional for over 10 years and I had tune ups that only took me 30 minutes, and others where it seemed like I had to practically disassemble the entire furnace, clean, then put back together. Every call is unique. However, it's important you trust your contractor. Your instincts are more accurate than you probably give yourself credit for. I don't remember a tune up ever going less than a 1/2 hr in my 10 years of experience. It just takes time to setup, take down, and perform the actual maintenance. If you figure a minute per inspection point, it should have at least taken half an hr. I've showed up to furnaces that look flawless, and I still take them apart and clean them because that's what the homeowner paid me for. If there is even a hint of a cracked heat exchanger, get a second opinion. There are scams out there, and unfortunately a 20 minute inspection wouldn't reveal that. Have whomever is making the claim show you via camera or by physically removing the combustion chamber from the furnace and showing you. As weird as that sounds, I've removed heat exchangers out of furnaces just to prove that there was an issue. A cracked combustion chamber can be a serious issue, so the fact that he said it should be fine says either he doesn't know what he's doing or he's not being truthful, or both. It's not that cracked heat exchangers are leaking carbon monoxide, it's that they can. It's the potential that makes it dangerous. Hope this helps!
Cut down on energy costs and prevent damage to your furnace by addressing a gas furnace that's overactive or short cycling. Besides the need for consistently comfortable temperatures, this issue could cause long-term safety issues to your home, making it very important to address. From a faulty thermostat to a dirty filter, there are several possible causes to investigate.
×