There’s a common misconception that you can save money by shutting the vents (supply registers) in rooms that aren’t being utilized. Resist the urge to close too many, as doing so can actually increase the pressure in your furnace, making it work harder to heat your home. This can lead to failed blower motors, mold or mildew in your ductwork, damage to the compressor, a cracked heat exchanger, and other problems. What Does a Furnace Tune-Up Include?

A pinging or popping sound coming from the duct work can come from thermal expansion—the ductwork expanding and contracting as it heats and cools.  Or, air blowing past a loose flap of metal can make the sound. Track along the duct runs, listening for the sound. If you locate it, make a small dent in the sheet metal to provide a more rigid surface that’s less likely to move as it heats and cools.
The cost to replace your entire unit is around $4,000. That expense can range from $2,500 to $5,900, depending on the type and brand of furnace you choose. Brands particularly have an impact on that price. A Goodman electric furnace, will only cost about $2,100 for the unit and labor. On the other hand, a Trane oil furnace may cost up to $9,000 all things considered. Our Furnace Installation Cost Guide can give you a better idea on both the general cost and the differences for brands like Amana, Bryant, Coleman, and others. The brand also plays into the repair cost for your furnace. Especially the prices of individual parts can change; a York heat exchanger, for example, can cost up to $1,900, while the same component from Heil will cost as little as $400.

Sky Heating & Air Conditioning provides a wide range of quality HVAC services to homeowners across Portland and The Dalles.  By bringing together skilled technicians and premier products, we deliver superior value for your investment.  We utilize tried and true strategies to enhance efficiency, comfort, and convenience throughout your home.  For heating and air conditioning installation, repair, and regular maintenance, no one takes better care of you than Sky Heating & Air Conditioning.  And we’re always here!  Count on us 24 hours a day, 7 days a week, to protect your safety, comfort, and best interests.

There are a lot of problems you may encounter with your water heater, but there are also a lot of warning signs that can tip you off to the fact that repairs are necessary. Unreliable or insufficient hot water, as well as increased hot water costs, are among the most common. Give us a call to ensure that your water heater repair in Kirkland, WA is completed promptly.
The thermocouple is a copper rod that the pilot flame heats-up. When it gets hot enough, the thermocouple signals that there is enough heat to burn the gas fuel being released into the appliance—and so it allows the gas to be released to the burners. In some cases where the pilot light won’t stay lit, the thermocouple needs to be adjusted or replaced. This is generally a job for a professional.
The cost to replace your gas furnace will vary based on the type and size of furnace you select, labor and installation costs, and any repairs your HVAC system may need. Nationally, average HVAC prices for a heating specialist range between $1,800 and $2,500. It’s important to select the right size gas furnace for your heating needs. A furnace that’s too small won’t heat your house properly, while a furnace that’s too large will run inefficiently, cycling on and off and likely breaking down sooner. HVAC specialists calculate your exact heat needs by measuring your home and incorporating variables such as the regional climate and your home’s level of insulation. Retail pricing for gas furnaces can range from $650 up to $3,000 and more. The higher the AFUE (annual fuel utilization efficiency) rating of the furnace, the more efficient it is at turning fuel into heat and the lower your carbon footprint and utility bill will be. HVAC installation costs are often based on an hourly rate and can range from under $50 to over $100 per hour, depending on the company and the furnace being installed. Higher-end furnaces cost more to install because they require added labor and expertise. For a typical installation, it might take two HVAC installation pros one day or less to remove your old furnace and replace it with a new one.
The oil filter (found in oil-powered systems only) prevents small impurities from clogging the oil-burner nozzle, which could result in a misfire that shuts down the system. Richard first closes the oil valve, then removes the old filter and replaces it, setting aside the dirty filter to be disposed of according to local hazardous-waste regulations.

You can help prevent issues with your system by scheduling routine maintenance on your furnace every year. During a maintenance visit, our technician will inspect and clean your furnace to help the system to run more smoothly and efficiently for the coming winter. You can have it done any time, but the maintenance is typically performed in the fall. Ask about our planned service agreement program!

The thermocouple is a copper rod that the pilot flame heats-up. When it gets hot enough, the thermocouple signals that there is enough heat to burn the gas fuel being released into the appliance—and so it allows the gas to be released to the burners. In some cases where the pilot light won’t stay lit, the thermocouple needs to be adjusted or replaced. This is generally a job for a professional.
Whether its gas pressure that needs adjusting or an inducer fan motor that needs replacing; We offer a 100% customer satisfaction guarantee for everything that we do. You never have to hesitate to contact Signature Heating, Cooling & Plumbing at 505-365-1885 regarding your heating service needs. We service ALL brands! Financing is available for big jobs.
When a furnace maintenance is performed a combustion analysis should be performed to identify any problems that couldn't be found by a visual inspection. You want to know what the Carbon monoxide level your furnace is producing as well as the oxygen/CO2 levels and stack temperate. The analyzer will also give you a calculated efficiency rating with the information the analyzer receives. You should have >100ppm of Carbon monoxide output during normal operation of your gas furnace. When you have higher numbers or CO numbers increasing during operation their is a problem with the furnace the technician should then find the cause of. This is just a brief explanation I'm trying to get across to those who get their furnace maintained and to those who don't! Check to see if anyone in the company has a NCI certification for carbon monoxide/combustion analysis.

Furnace Service Company

×