The US Environmental Agency recognizes geothermal heating & cooling as the most environmentally-safe, cost effective heating and cooling system on the market. A typical 2000 square foot home can be heated or cooled for as little as a dollar a day. As one of the biggest and most experienced geothermal companies in the Cohoes area, Choice Heating & Cooling has the resources, expertise and practical knowledge to design and execute this groundbreaking technology, enhancing home comfort and energy savings

“Walter Zainey started the Greenwood Furnace Co. in the Greenwood neighborhood of Seattle in 1918 and quickly built a reputation for providing quality products and services. For years we believed Greenwood began in 1921 but only recently, May of 2017, Walter’s granddaughter shared a newspaper ad from 1968 showing that Greenwood was actually founded in 1918! When your company goes back 100 years you are bound to have mixed messages about the history but we now have an accurate founding date and founder. Thank you to the Zainey family and especially Jacklyn for taking the time to share the story with us. I am sure Walter Zainey would be proud the heritage he created is still living on.
Richard checks for holes in the exhaust flue that could leak carbon monoxide, particularly where the pipe meets the furnace. Small holes can be patched with foil tape, but corroded flues must be replaced. He also adjusts the flue pipe's barometric damper, which moderates the chimney draw. "A big, tall chimney in an old house tends to suck too much air, compromising efficiency," he says. "Your service pro can weight the damper to lessen the draw.
If your furnace’s motor runs but the blower doesn’t move air, the belt that connects the two probably has broken. Replacing it is an easy fix. First, turn off all power to the unit and turn off the gas at the gas valve that serves the furnace. Remove the door on the front of the furnace cabinet to give you access to the blower (it might be on a slide-out drawer.) Check the number stamped on the belt and get an exact replacement from a home center or heating supply outlet.
Whether you’re looking to have a heat pump installed for the first time or think it’s time for an upgrade to your current system, Goettl Air Conditioning is the company to call. We offer a great lineup of Phoenix heat pumps and will make sure that the one we install in your home is the recommended match to your home’s dimensions and your family’s needs.
Before performing DIY furnace maintenance, Richard makes sure to switch off the electrical power and the fuel supply. The distinctive red power switchplate can usually be found at the top of the cellar stairs or near the burner itself, while the fuel shutoff valve is near the oil tank or on the incoming gas pipe. Note the location of both in case of a future leak or fire.
We came home to a gas leak and our CO detector going off last Thursday (was very cold out)! After contacting Natl Fuel we proceeded to call Nerthlings for help! They arrived quickly, found the problem & worked with us to install our new furnace the next day. They were great to deal with & a huge help with the bad weather we were having at the time!

As a technical industry, the heating and cooling field is associated with annual advances. New energies make our industry an exciting place to work. Our team thrives on keeping up to date with all changes in the HVAC field. We are here to share our knowledge with each customer. When you are ready to update your HVAC system, we can help you select the ideal system for your home.
Furnaces and thermostats are not mix-and-match appliances. Using the wrong type of thermostat with a furnace will cause operating problems and can be dangerous. Although thermostats look similar, they are designed very differently. There are numerous types of heating systems and thermostat systems and they need to be coordinated for safe and proper operation. There are three types of thermostat systems used today: millivoltage, low voltage, and line voltage.​
Though forced-air furnaces are normally quite reliable, they can break down. To avoid break downs, it pays to know how to take care of your furnace and fix it when something goes wrong. Inevitably, a furnace stops working when you need it most. Consequently, fixing becomes urgent very quickly. The following instructions will help. With a little do-it-yourself experience and the proper guidance, you can troubleshoot and repair a variety of furnace problems yourself.

Moncrief provides a wide range of services from high-quality energy-efficient systems, tune-ups and inspections, as well as repairs in the Roswell and Marietta areas. As a full-service heating and cooling company, we stay up-to-date on the most economical and energy-efficient systems available for your home or business. In addition, our technicians are well-trained in a wide range of systems to provide quality and cost-efficient furnace service, repairs and installation.
Furnace tune ups should take anywhere from 45 minutes to hour and a half, depending on what the technician has to deal with when he gets there. I was a heating and AC professional for over 10 years and I had tune ups that only took me 30 minutes, and others where it seemed like I had to practically disassemble the entire furnace, clean, then put back together. Every call is unique. However, it's important you trust your contractor. Your instincts are more accurate than you probably give yourself credit for. I don't remember a tune up ever going less than a 1/2 hr in my 10 years of experience. It just takes time to setup, take down, and perform the actual maintenance. If you figure a minute per inspection point, it should have at least taken half an hr. I've showed up to furnaces that look flawless, and I still take them apart and clean them because that's what the homeowner paid me for. If there is even a hint of a cracked heat exchanger, get a second opinion. There are scams out there, and unfortunately a 20 minute inspection wouldn't reveal that. Have whomever is making the claim show you via camera or by physically removing the combustion chamber from the furnace and showing you. As weird as that sounds, I've removed heat exchangers out of furnaces just to prove that there was an issue. A cracked combustion chamber can be a serious issue, so the fact that he said it should be fine says either he doesn't know what he's doing or he's not being truthful, or both. It's not that cracked heat exchangers are leaking carbon monoxide, it's that they can. It's the potential that makes it dangerous. Hope this helps!
You might guess it from the name: the heat exchanger is the part of your furnace that actually heats the air your blower motor pushes through the furnace. It consists of a chamber in which the heat energy produced by natural or propane gas is transferred to the forced air. At the same time, this part also includes a vent through which the gases themselves are safely removed from the unit and the air that enters your home. Because of these gases, a problem with your heat exchanger needs to be dealt with promptly. Over time, cracks in the exchanger can result in carbon monoxide leaks. Taking care of the problem once again means understanding the existence of a range: repairing your heat exchanger can cost as little as $100, but a full replacement may cost up to $1,200.
As touched on by their name, heat pumps function by transferring heat energy indoors during the winter and outdoors from your home during the summer. They're often attached to air conditioning units, using the surrounding air to transfer energy. However, geothermal heat pumps and water source heat pumps are also available. The cost to repair a heat pump, again, depends on the specific problem. Replacing a faulty thermostat may cost up to $300 including labor, while a worn or damaged defrost control board can set you back up to $600. For more details on your potential repair costs using this heating source, visit our heat pump repair cost guide.

Vredevoogd Heating & Cooling Grand Rapids values each and every customer. Servicing or installing your HVAC system means establishing a service relationship with each homeowner. We promise to earn your trust with our consummate level of professionalism and expert service. We back our work with the strongest industry guarantees because we value your continued business.
You can usually slip the belt on the motor’s (smaller) pulley first and then start it on the blower pulley. Rotate the blower pulley by hand, holding the belt in place but keeping your fingers from getting caught between the belt and the pulley. The belt should slip right into place. If it seems to be too tight or difficult to set in place, it may be necessary to adjust the motor mount to provide more slack.
Your heating and air conditioning system naturally loses energy efficiency over time. This loss of efficiency is due to many factors, including dust and dirt, natural wear and tear, and buildup in drains or on burners. Keeping your heating system maintained with regular professional tune-ups can help to reduce these factors. During your tune-up, your maintenance technician will clean and check over your heating equipment, identifying areas of wear and tear. They can identify failing parts in need of replacement before they become a serious problem. A tune-up alone may instantly improve energy efficiency by up to 30%. You’ll also enjoy cleaner air and a cleaner residence because your HVAC system will be distributing clean air through a clean air filter. Perhaps one of the greatest benefits you’ll enjoy following a fall furnace or AC tune-up is decreased utility bills. A neglected HVAC system must work much harder to heat and cool your home, while a furnace or air conditioner that has been finely tuned can take less energy to maintain indoor comfort. Because your heating system will function more efficiently, it will deliver superior heating at lower cost than you otherwise may have had through the winter season.
When your furnace filter becomes dirty, dusty and clogged, you can expect some negative effects on your furnace efficiency and your indoor air quality. The forced air is supposed to get blown through the filter and the filter is supposed to trap any particles so they don’t end up in your air ducts and throughout the house. When the filter has trapped too many particles and it is clogged up, the air keeps blowing, but some of those trapped particles will end up in the system and your living space. Another effect is that the furnace has to work harder to get the same amount of air through that dirty filter, so your heating bills may go up.
*Service Call Fee waived with any completed repair and includes inspection of your system. Not valid for commercial services. Does not include repairs or replacements. Valid at participating ARS® / Rescue Rooter® Network locations. Not valid for third party, new construction customers, with any other offers or discounts, or prior sales. Coupon required at time of service. Void if copied or transferred and where prohibited. Any other use may constitute fraud. See service center for details. Cash value $.001. License # TACLA018810E R. Hoffart, MPL41408 S. Neidig, TECL28671 M. James. Offer expires 11/30/2018.
Whether you’re looking to have a heat pump installed for the first time or think it’s time for an upgrade to your current system, Goettl Air Conditioning is the company to call. We offer a great lineup of Phoenix heat pumps and will make sure that the one we install in your home is the recommended match to your home’s dimensions and your family’s needs.

AAA Heating and Cooling has been the leader in residential and commercial furnace installation, heating services and air conditioning repair for thousands of clients throughout Portland, Beaverton, Hillsboro, Lake Oswego and the surrounding areas for over half a century. As a family-owned Portland, OR business, we offer a variety of services, including the installation of home heating and air conditioning systems, AC and furnace service and repair, duct cleaning as well as a variety of commercial heating and cooling solutions.

Heating Repair

×