Our goal is to make you more comfortable in your home. When your furnace, central air conditioner, heat pump or boiler stops working and you need service, call the professionals at BGE HOME. Heating and cooling system breakdowns occur at the most inconvenient times, so rely on our certified, skilled technicians to make the repair quickly and correctly the first time.
This job involves removing the access panel, loosening a couple of bolts that hold the blower motor at the proper tension, and adjusting its distance or realigning the belt. In many cases, it’s a good idea to remove the belt and buy a replacement at a home center. Last, when reinstalling the belt, be careful not to over-tighten it; this can wear out the motor bearings.
High-efficiency condensing furnaces (90% AFUE and above) are a bit more complex than conventional furnaces. The main differences between a conventional and condensing furnace are the heat exchanger technology used to extract heat from the combustion process and the method used to exhaust the combustion gases. In these ways, the furnaces are very different. The condensing furnace does not have a significantly more efficient combustion process than does a conventional furnace; both use gas burners with electronic ignition. The difference lies in that the condensing furnace has a more efficient heat extraction process after combustion.
In a lot of homes, in Chicago Illinois, the initial HVAC installation was banged together to get it done. We’ve found big errors in heat system installations, like heat registers that aren’t hooked up and ducts that are open and pumping heat into your crawlspace or attic, or thermostats installed in the wrong place. Our Heating system technicians can survey your HVAC system and suggest improvements that will improve your comfort and save you wasted fuel bills.
Before performing DIY furnace maintenance, Richard makes sure to switch off the electrical power and the fuel supply. The distinctive red power switchplate can usually be found at the top of the cellar stairs or near the burner itself, while the fuel shutoff valve is near the oil tank or on the incoming gas pipe. Note the location of both in case of a future leak or fire.

Before performing DIY furnace maintenance, Richard makes sure to switch off the electrical power and the fuel supply. The distinctive red power switchplate can usually be found at the top of the cellar stairs or near the burner itself, while the fuel shutoff valve is near the oil tank or on the incoming gas pipe. Note the location of both in case of a future leak or fire.
We are service professionals! As licensed contractors and specialists in the field of heating and air-conditioning, we have the tools, the equipment, and the experience to keep your equipment running smoothly all year long. If it is emergency service that you need, Twenty-four hours a day, seven days a week, we are available to assist you! To help reduce service emergencies, we offer service agreements to keep your comfort system running at peak performance.
A number of other variables can influence your decision on whether to repair or replace your furnace, as well. In addition to cost and brand, consider the expected lifetime of your furnace. If it is more than 15 years old, it might make more sense to invest in a new unit even if it costs more than simply repairing the current problem. Long-term costs also play into the equation. For example, your new furnace may be more energy efficient than the current unit. Even though you will pay more for the actual installation, you might be able to make back your investment through lower energy bills. To make your decision, consult with a reliable professional on what to do. In inspecting your furnace, they will be able to make an informed recommendation that looks not just to the next year, but years into the future. That way, you can make the best possible decision for your home and budget long-term.
Advice you can count on – When you have an emergency, you are not always in the position of asking questions to determine if the repairs you are receiving are what you need. At Jennings, our NATE Certified technicians will walk you through the repairs and explain why you need them. You can trust that everyone on Jennings’ staff will give you honest advice.
Given the broad price ranges above, it's easy to recognize that the cost of your furnace repair varies drastically based on which parts need attention. As a result, it makes sense to gain a better understanding of the parts that heat your home, and how much they cost to repair. Repairing or replacing your furnace’s blower motor can cost you anywhere between $150 and $450, depending on the extent of the damage. Heat exchanger repair costs can vary greatly, from as little as $100 for a simple fix to as much as $1,200 for a full replacement. Repairing a furnace igniter will only cost you $300 at most, while flame sensor repairs generally fall between $80 to $250. The average cost to repair your Thermostat will range from $108 to $282.
Do not try to do DIY gas furnace maintenance or tune-ups yourself. In addition to being dangerous, this may also violate the manufacturer’s warranty. Let properly trained and experienced technical staff perform all gas furnace preventative maintenance. Regardless of your DIY talent, trying DIY furnace maintenance is fraught with hazards and risks to your heating system—and yourself.
When your furnace needs a repair, trust the professionals at BGE HOME. We’ll show up on time and in uniform, and fix your furnace correctly the first time. Plus, our technicians are available 24-hours a day for emergency repairs . To schedule a furnace repair online , use the link below and have peace-of-mind knowing that a licensed, certified HVAC technician will have your system up and running as quickly as possible. For 24-hour emergency furnace repair service, call 1-888-243-4663.
Put simply, any home that uses air pushed through ductwork for heating purposes takes advantage of forced air heating. In other words, this term refers not to your furnace, but to the delivery method of the heat throughout your home. Forced air heating is possible with electric or gas furnaces, or a heat pump. Any issues with this delivery system that aren't directly related to the furnace likely have to do with the duct work, which costs between $35 and $55 per linear square foot to repair, or the air handling unit.
Furnace tune ups should take anywhere from 45 minutes to hour and a half, depending on what the technician has to deal with when he gets there. I was a heating and AC professional for over 10 years and I had tune ups that only took me 30 minutes, and others where it seemed like I had to practically disassemble the entire furnace, clean, then put back together. Every call is unique. However, it's important you trust your contractor. Your instincts are more accurate than you probably give yourself credit for. I don't remember a tune up ever going less than a 1/2 hr in my 10 years of experience. It just takes time to setup, take down, and perform the actual maintenance. If you figure a minute per inspection point, it should have at least taken half an hr. I've showed up to furnaces that look flawless, and I still take them apart and clean them because that's what the homeowner paid me for. If there is even a hint of a cracked heat exchanger, get a second opinion. There are scams out there, and unfortunately a 20 minute inspection wouldn't reveal that. Have whomever is making the claim show you via camera or by physically removing the combustion chamber from the furnace and showing you. As weird as that sounds, I've removed heat exchangers out of furnaces just to prove that there was an issue. A cracked combustion chamber can be a serious issue, so the fact that he said it should be fine says either he doesn't know what he's doing or he's not being truthful, or both. It's not that cracked heat exchangers are leaking carbon monoxide, it's that they can. It's the potential that makes it dangerous. Hope this helps!
Thornton, CO residents trust in Marky Mark's Heating, Cooling & Plumbing, LLC for all of their heating and air conditioning service needs. Contact our heating company for furnace installation and furnace repair, as well as a range of air conditioning and plumbing services. Our team of technicians specializes in indoor comfort solutions. Call anytime! Learn more…
At Sky Heating & Air Conditioning, we understand that HVAC services can really hurt your budget. Many times, you don’t expect to make such large purchases until an emergency arises. We never want you to feel that you cannot afford your comfort and safety. We offer flexible financing options through the Home Project credit card from Wells Fargo, with approved credit. Head over to our financing page to apply, or give us a call for more information!

When your furnace needs a repair, trust the professionals at BGE HOME. We’ll show up on time and in uniform, and fix your furnace correctly the first time. Plus, our technicians are available 24-hours a day for emergency repairs . To schedule a furnace repair online , use the link below and have peace-of-mind knowing that a licensed, certified HVAC technician will have your system up and running as quickly as possible. For 24-hour emergency furnace repair service, call 1-888-243-4663.

The cost to replace your entire unit is around $4,000. That expense can range from $2,500 to $5,900, depending on the type and brand of furnace you choose. Brands particularly have an impact on that price. A Goodman electric furnace, will only cost about $2,100 for the unit and labor. On the other hand, a Trane oil furnace may cost up to $9,000 all things considered. Our Furnace Installation Cost Guide can give you a better idea on both the general cost and the differences for brands like Amana, Bryant, Coleman, and others. The brand also plays into the repair cost for your furnace. Especially the prices of individual parts can change; a York heat exchanger, for example, can cost up to $1,900, while the same component from Heil will cost as little as $400.

When our Denver heating company provides you with maintenance checks before the cold of winter sets in, you will be saving money in several different ways. One of the benefits of a maintenance plan is our technicians will be less likely to have to make repairs throughout the year as long as the system is properly maintained. Our Denver heating company will have your system running at its most efficient, helping to reduce your utility bills each month. An added benefit of a more efficiently running system is the positive environmental effect that it will have.


Your furnace's flame sensor is essentially a safety mechanism. As a thin metallic rod in front of the flame inside the unit, it's sole purpose is to confirm that your gas valves only open when a flame actually exists to burn that gas. When the flame sensor stop working, on the other hand, gas leaks can occur. To repair your furnace's flame sensor, expect to spend between $80 and $250. Even a full replacement of this part typically does not go above that range.
Our Aurora furnace repair company only employs the highest quality professionals. We realize that dealing with a furnace is very serious, and we only have workers that are highly experienced in doing so. In order to deal with the best company that specializes in furnace replacement in Aurora and furnace repair in Aurora, you have to be sure that the company is professional and committed to a quality customer service experience.
We live in a recently completed townhouse that was built with double-wall construction. That construction method was touted by the builder as what would keep sound from penetrating between the units. But we can hear the next door neighbors' TV and stereo, and sometimes voices and even snoring, through the wall. While sometimes it's the volume, mostly it's the bass sounds coming through the wall. They say they don't hear us, but we keep our bass turned down. They crank up the bass, and they are not going to change that. They also are not going to do anything construction-wise to help from their side. What is the best way for us to try to block the low frequency/bass sounds from penetrating the existing wall into our side?
At Bob’s Heating & Air Conditioning, we believe that our customers deserve to live comfortably throughout the entire year. That is why we offer such a comprehensive selection of air conditioning, heating and water heater services in Kirkland, WA. When you work with us, you can rest assured that your furnace is installed properly, your AC maintenance is meticulous, and that your water heater repairs are top notch. Contact us today to learn more about the heating and cooling services we offer throughout Kirkland, WA.

Furnace Service Company CO

×