No one wants to be stuck in the dead of summer with a broken air conditioner, or in the cold of winter with a broken furnace or boiler. That’s why we’re available any time of day to make your emergency heating and air conditioning repair and get your system up and running as quickly as possible. We’ll show up on time, in uniform and ready to make your HVAC repair right the first time.
B&B Heating & Air Conditioning is a Carrier Factory Authorized Dealer, a recognition that is earned rather than given.  Our service team is fully insured, certified, and receives ongoing factory training at the highest level. To further protect your best interests, our technicians do not work off commission.  We provide honest, ethical, and no-pressure service, and offer recommendations that serve your long-term satisfaction.
Regarding your post, Every technician performs a maintenance differently. Today's modern furnaces really don't require as much maintenance as older style systems did. For instance: Older furnaces had drive belts, pulleys and motors with oil ports.Today's blowers are direct drive no belts, no pulleys, sealed bearing motors no oiling required. All of the new modern technology cuts the maintenance time in half if not more. Today's equipment has multiple safety's in place so that in case of a failure the system will shut down. non serviceable control boards or (Brains) monitor system functions. Unlike oil systems, the maintenance on a gas system can possibly be completed in less than half the time. I'd say 20 to 30 minutes is about right unless a service issue arises. In the 30 minute time span, the doors can be removed, system components can be visually inspected, the flame can be inspected and co test can be performed for spillage and vacuum of the combustion area can be performed if needed. The air filter should be checked and the humidifier can be activated. Remember that probing into a perfectly functioning system can be detrimental to its lifespan. My advice is change you air filter, keep the area around the equipment free of dust and try not to store in close proximity to the heating plant. Be sure you have an updated quality carbon monoxide detector in your home. Regarding the crack in your heat ex-changer, If the heat ex-changer had a crack in it, the system it should have been shut down right then and there. Be aware that Carbon monoxide may be entering your living space due to that crack. Have a knowledgeable company come back and do a CO test in your home at the supply vents and use a scope to check your heat ex-changer for cracks. I hope this helps you. Bottom line, you have to trust the company that you are using. If you feel uncertain about their capabilities, then more than likely, you instinct is correct. Good Luck to you.. Happy Holidays
The motor belt should be firm, giving no more than ½ inch when pressed. It should also be free of cracks and damage. To remove the belt, you will need a wrench and a replacement belt. Loosen, do not remove, the motor bolts. You only need them loose enough to move the motor and slacken the belt. Remove the belt and inspect it, replacing it with a new one if necessary. Belt: $4.00 to $6.00.

For more than sixty years, Nerthling's Heating and Air Conditioning has continued a tradition of superior customer service across Erie County, including Erie, Millcreek and Fairview.  Family owned and operated, we treat you, your home, and your comfort the way we would like to be treated.  This commitment to integrity extends to every service and product we provide.  Our goal is to deliver the highest rewards for your investment, whether you require installation, maintenance, or repair.  We offer a wide range of styles and sizes of equipment, services, and resources to help you achieve your goals for temperature control, air quality, and energy savings.
Seattle furnaces can run nine months of the year. Based on the average temperatures in our area, if you compared running your furnace to a car it would get the equivalent of 1.8 million miles over its expected lifespan of 15 years. Your heating system will work hard for you, but like your car, doing routine and regular maintenance will keep it running smoothly, avoid problems, and keep your warranty intact.
Your heating and air conditioning system naturally loses energy efficiency over time. This loss of efficiency is due to many factors, including dust and dirt, natural wear and tear, and buildup in drains or on burners. Keeping your heating system maintained with regular professional tune-ups can help to reduce these factors. During your tune-up, your maintenance technician will clean and check over your heating equipment, identifying areas of wear and tear. They can identify failing parts in need of replacement before they become a serious problem. A tune-up alone may instantly improve energy efficiency by up to 30%. You’ll also enjoy cleaner air and a cleaner residence because your HVAC system will be distributing clean air through a clean air filter. Perhaps one of the greatest benefits you’ll enjoy following a fall furnace or AC tune-up is decreased utility bills. A neglected HVAC system must work much harder to heat and cool your home, while a furnace or air conditioner that has been finely tuned can take less energy to maintain indoor comfort. Because your heating system will function more efficiently, it will deliver superior heating at lower cost than you otherwise may have had through the winter season.
Vredevoogd Heating & Cooling Grand Rapids employs more than 80 people who are proud to work under the Vredevoogd Heating & Cooling banner. Each team member shares our company values for service excellence. All of our employees are intensely screened and background checked so that you have peace of mind when they enter your home. Moreover, our technicians are certified to work in the HVAC industry and provide the level of expertise that our customers expect from Vredevoogd Heating & Cooling. We back our technicians’ work and continue to make training a priority so that all of our techs are familiar with the latest HVAC models and advances. Our customers deserve the best, so the best is what we deliver to each and every job.

CM Heating performed a Gas Furnace Diagnostic. Customer wanted his echo bee thermastat installed that he had bought himself. Furnace was working fine just wanted his thermastat installed. He thought that the $99 service fee was going to cover that but explained to him what the service fee was for, and explained that there is a additional install fee for the stat. Customer didn’t want to pay the additional fee so I called the office had them listen to the call to make sure we explained to the customer correctly and to see how they would like me to proceed. So I quoted the customer the fee to install the thermostat but he didn’t want us to install it so I left.


Thornton, CO residents trust in Marky Mark's Heating, Cooling & Plumbing, LLC for all of their heating and air conditioning service needs. Contact our heating company for furnace installation and furnace repair, as well as a range of air conditioning and plumbing services. Our team of technicians specializes in indoor comfort solutions. Call anytime! Learn more…
No one wants to be stuck in the dead of summer with a broken air conditioner, or in the cold of winter with a broken furnace or boiler. That’s why we’re available any time of day to make your emergency heating and air conditioning repair and get your system up and running as quickly as possible. We’ll show up on time, in uniform and ready to make your HVAC repair right the first time.
If your thermostat has a small lever that moves along a calibrated scale that indicates “longer” (not the heat temperature lever), you can try adjusting this—the heat anticipator. Just set it one calibration mark closer to the “longer” setting if the furnace goes off and on too frequently or one mark away if the furnace allows room temperature to rise too high or drop too low before going on or off. It may take several hours for the thermostat to stabilize at this setting, so wait a while and then adjust it again if necessary.
As a family-owned business, we take care of our customers with a comprehensive list of services, including heating and cooling installation, maintenance and repair, boiler installation and service, hot water heater service and geothermal systems.  We protect your best interests and strive to eliminate inconvenience through emergency service, free estimates, flexible financing, and 10 year parts & labor warranty included on new furnace installations.  Call Choice Heating & Cooling for your home comfort needs and expect more.  From your initial inquiry to the completion of the job, our goal is to exceed your expectations in every service we provide.
Many things can go wrong with your furnace, all of which should be repaired and examined by experienced professionals. Trust Randazzo Heating, Cooling, and Fireplaces to repair and help you maintain your furnace*. We value our customers and their decisions, so we will always be honest and explain the best possible solution for you. Contact us today so we can help you out! Click Here for our warranty policy.

You can usually slip the belt on the motor’s (smaller) pulley first and then start it on the blower pulley. Rotate the blower pulley by hand, holding the belt in place but keeping your fingers from getting caught between the belt and the pulley. The belt should slip right into place. If it seems to be too tight or difficult to set in place, it may be necessary to adjust the motor mount to provide more slack.


The motor belt should be firm, giving no more than ½ inch when pressed. It should also be free of cracks and damage. To remove the belt, you will need a wrench and a replacement belt. Loosen, do not remove, the motor bolts. You only need them loose enough to move the motor and slacken the belt. Remove the belt and inspect it, replacing it with a new one if necessary. Belt: $4.00 to $6.00.
Do not try to do DIY gas furnace maintenance or tune-ups yourself. In addition to being dangerous, this may also violate the manufacturer’s warranty. Let properly trained and experienced technical staff perform all gas furnace preventative maintenance. Regardless of your DIY talent, trying DIY furnace maintenance is fraught with hazards and risks to your heating system—and yourself.
When a furnace maintenance is performed a combustion analysis should be performed to identify any problems that couldn't be found by a visual inspection. You want to know what the Carbon monoxide level your furnace is producing as well as the oxygen/CO2 levels and stack temperate. The analyzer will also give you a calculated efficiency rating with the information the analyzer receives. You should have >100ppm of Carbon monoxide output during normal operation of your gas furnace. When you have higher numbers or CO numbers increasing during operation their is a problem with the furnace the technician should then find the cause of. This is just a brief explanation I'm trying to get across to those who get their furnace maintained and to those who don't! Check to see if anyone in the company has a NCI certification for carbon monoxide/combustion analysis.
This job involves removing the access panel, loosening a couple of bolts that hold the blower motor at the proper tension, and adjusting its distance or realigning the belt. In many cases, it’s a good idea to remove the belt and buy a replacement at a home center. Last, when reinstalling the belt, be careful not to over-tighten it; this can wear out the motor bearings.
If your heating system in Bothell, WA is not working it is likely your furnace needs repair or service. At times the fix is simple, other times it is not. Our heating and furnace service technicians have years of experience working on furnaces like yours in Bothell, WA. C.M. Heating has service vehicles on call that are fully equipped with the tools and parts necessary to get your furnace back up and operating.
Vredevoogd Heating & Cooling technicians routinely assist our customers to figure out when it’s time to upgrade their Heating or Cooling system. Naturally, repairs are part of routine maintenance over the years. However, new models can save homeowners in a big way on energy expenses with their energy-efficient makeup. When you are ready to get a new system, we will do a careful check of your energy needs so that you can select the ideal system for your home’s needs. The wrong HVAC system for your home is a 15 year mistake that no one should have to afford. We install the right system for your home. Moreover, we offer guarantees that you won’t find just anywhere else. If your new installation isn’t right for your home, we’ll remove it free of charge at any time within that first year and refund 100% of your money. Our customers are burdened with no risks. We take on the risk because we are that sure of our expertise. We back our work with the strongest warranties in the field. In fact, we offer a wide array of warranties to provide you with the peace of mind you deserve as a valued Vredevoogd Heating & Cooling Grand Rapids MI customer.
When a family chooses to work with Brothers Plumbing Heating And Electric they will not be disappointed. We are able to work on a very tight schedule and we know just what it takes to service a furnace. There is no doubt about it, a family does well to look into Brothers Plumbing Heating and Electric because we are truly the best Aurora furnace repair company. To learn more about heating and cooling systems, just give this page a visit today!
At Horizon Services, we strive to provide all of our customers with the peace of mind that comes from knowing that you have a skilled team on-call for any AC emergencies that may arise. We have more than 300 fully stocked trucks ready to go at a moment's notice. Our Horizon technicians undergo rigorous training, including a mandatory 150 hours of training every year, to ensure that they're always up to date on the latest techniques and HVAC technology. Plus, we perform extensive background checks, including drug and criminal checks, on all of our employees so you don't have to worry about letting a stranger into your home when your AC breaks down in the middle of the night. When you're dealing with an air conditioning emergency, trust the experts at Horizon Services!
Although San Antonio is known more for its heat than its cold, here at Will Fix It, we’ve helped thousands of Texans keep warm during our many cold snaps with a quick heating repair. We have professional HVAC technicians who have repaired and serviced all kinds of heating systems. Let one of our experienced technicians offer a reliable diagnosis of the issue and provide an upfront, written estimate that includes options and recommendations. No work is done until you approve.
AAA Heating and Cooling has been the leader in residential and commercial furnace installation, heating services and air conditioning repair for thousands of clients throughout Portland, Beaverton, Hillsboro, Lake Oswego and the surrounding areas for over half a century. As a family-owned Portland, OR business, we offer a variety of services, including the installation of home heating and air conditioning systems, AC and furnace service and repair, duct cleaning as well as a variety of commercial heating and cooling solutions.
If your furnace sputters to a halt during the evening or overnight in the middle of winter, you can bet that the indoor temperature will plummet by morning and everyone will be cold and uncomfortable. It isn’t as bad as outside because you have wind protection and residual heat, but no one in the house will be happy. The key to finding a quick solution to these kinds of scenarios is to align yourself with a reputable, reliable service provider before there is a problem. If you have a local expert in your corner, you can call as soon as something happens and your service disruption will be minimal.
High-efficiency condensing furnaces (90% AFUE and above) are a bit more complex than conventional furnaces. The main differences between a conventional and condensing furnace are the heat exchanger technology used to extract heat from the combustion process and the method used to exhaust the combustion gases. In these ways, the furnaces are very different. The condensing furnace does not have a significantly more efficient combustion process than does a conventional furnace; both use gas burners with electronic ignition. The difference lies in that the condensing furnace has a more efficient heat extraction process after combustion.
×