Locally owned and family operated, M and M, Heating & Cooling, Plumbing & Electrical customizes solutions to perfectly fit your requirements and lifestyle. We specialize in a wide range of services including plumbing, water heating, indoor air quality, and residential and commercial temperature control. Our team of highly trained and certified technicians are fully licensed and insured, adhere to strict service procedures, and meet exacting standards of quality. Call on M and M, Heating & Cooling, Plumbing & Electrical at (720) 443-6119 for dedicated service throughout Longmont, CO & surrounding areas, and have confidence in a rewarding experience and long-term results. With over eighteen years of satisfied customers, we take great pride in a job done right.
Your furnace's flame sensor is essentially a safety mechanism. As a thin metallic rod in front of the flame inside the unit, it's sole purpose is to confirm that your gas valves only open when a flame actually exists to burn that gas. When the flame sensor stop working, on the other hand, gas leaks can occur. To repair your furnace's flame sensor, expect to spend between $80 and $250. Even a full replacement of this part typically does not go above that range.
When your gas furnace isn’t blowing hot air, the issue could be due to a faulty pilot light or broken ignitor. Remove the furnace cover panel and visually inspect whether you can see a flame from the pilot light. A natural gas furnace will be blue and yellow in color, and a propane furnace should have a bluish green flame with a yellow tip. If you can see a flame and it appears normal, the issue could be related to the furnace blower motor or other complex furnace parts. If the flame appears low or non-existent, it’s best to contact an experienced furnace repair company. Remember to never touch any open wires; contact a professional.
The oil filter (found in oil-powered systems only) prevents small impurities from clogging the oil-burner nozzle, which could result in a misfire that shuts down the system. Richard first closes the oil valve, then removes the old filter and replaces it, setting aside the dirty filter to be disposed of according to local hazardous-waste regulations.
Whether you are looking for gas furnace service or repair, quality installation of a furnace, heat pump or air conditioner, mini split ductless heat pumps, endless hot water from tankless water heaters, better air quality in your home or just a filter change or duct cleaning, Greenwood Heating is your best choice of Seattle heating contractors and cooling specialists.
@Neil What is the use of repeating lessons when there is so much more to be learned? Technology has moved on from the adz. Plumbers use PEC, insulation is sprayed, glue-lams allow for open floor plans and furnaces are no longer stoked with coal. As for the new people, if these trades cannot attract fresh blood we will all be unable to get homes built and repairs made. I don't yearn for my first home with the leaky concrete block foundation, failing well pump and an oil furnace held up by the plenum. I'll take heat pumps, solar panels and PVC waste pipes any day.You can get all the sill plate repairs and flitch beams demos you need on YouTube.
Although San Antonio is known more for its heat than its cold, here at Will Fix It, we’ve helped thousands of Texans keep warm during our many cold snaps with a quick heating repair. We have professional HVAC technicians who have repaired and serviced all kinds of heating systems. Let one of our experienced technicians offer a reliable diagnosis of the issue and provide an upfront, written estimate that includes options and recommendations. No work is done until you approve.
The US Environmental Agency recognizes geothermal heating & cooling as the most environmentally-safe, cost effective heating and cooling system on the market. A typical 2000 square foot home can be heated or cooled for as little as a dollar a day. As one of the biggest and most experienced geothermal companies in the Cohoes area, Choice Heating & Cooling has the resources, expertise and practical knowledge to design and execute this groundbreaking technology, enhancing home comfort and energy savings
If you need a furnace repaired or an air conditioner serviced, we'll send a local technician out to diagnose the specific problem and recommend solutions for you and your family. There will be a diagnostic fee for the visit, and any specific repairs will be an additional charge. If replacing your system is the best solution, the fee for the diagnosis will be credited toward the purchase and install of a new system.

Whether you have an electric or gas furnace, you shouldn’t have to suffer when your heater is not working. At Sears Home Services, our technicians fix many of the top furnace manufacturers. The issues you may face with your furnace can vary depending on the type of heating system. If you own an electric model and it isn’t working, some of the potential causes include:
Don’t forget, when you’re in the need for 24 HR emergency repair in Akron, Ohio, Jennings is there for you no matter the time of day or night—24 hours a day and 7 days a week. If you have an emergency, please call 330-784-1286 now. If you would like to request service, please fill out and submit the form below and a Jennings associate will be in touch make an appointment.
Summers in Portland and The Dalles can be the absolute best time of year or pure torture.  Your cooling system makes the difference. Take advantage of perfectly maintained temperatures, superior dehumidification, unprecedented energy efficiency, and outstanding reliability with quality air conditioning products and services from Sky Heating & Air Conditioning.  We protect the enjoyment of your home with precise installation, system replacement, seasonal maintenance, and prompt repair.  Our skilled AC technicians are always on call 24 hours a day, 7 days a week, providing Emergency Service and protecting the value of your investment.  Every project is answered with a dedication to customer satisfaction that has earned us an A+ rating from the Better Business Bureau. Contact Sky Heating & Air Conditioning for air conditioning service in The Dalles and Portland, OR.  
An improperly maintained heating and air conditioning is an inefficient heating and air conditioning system. That’s why we provide appointments for annual inspections with our licensed technicians. It’s our goal to make sure that your home is as comfortable and energy-efficient as possible. For inspections, repairs, and service, contact BGE HOME for quality service.

You can help prevent issues with your system by scheduling routine maintenance on your furnace every year. During a maintenance visit, our technician will inspect and clean your furnace to help the system to run more smoothly and efficiently for the coming winter. You can have it done any time, but the maintenance is typically performed in the fall. Ask about our planned service agreement program!
The cost to replace your gas furnace will vary based on the type and size of furnace you select, labor and installation costs, and any repairs your HVAC system may need. Nationally, average HVAC prices for a heating specialist range between $1,800 and $2,500. It’s important to select the right size gas furnace for your heating needs. A furnace that’s too small won’t heat your house properly, while a furnace that’s too large will run inefficiently, cycling on and off and likely breaking down sooner. HVAC specialists calculate your exact heat needs by measuring your home and incorporating variables such as the regional climate and your home’s level of insulation. Retail pricing for gas furnaces can range from $650 up to $3,000 and more. The higher the AFUE (annual fuel utilization efficiency) rating of the furnace, the more efficient it is at turning fuel into heat and the lower your carbon footprint and utility bill will be. HVAC installation costs are often based on an hourly rate and can range from under $50 to over $100 per hour, depending on the company and the furnace being installed. Higher-end furnaces cost more to install because they require added labor and expertise. For a typical installation, it might take two HVAC installation pros one day or less to remove your old furnace and replace it with a new one.
Before performing DIY furnace maintenance, Richard makes sure to switch off the electrical power and the fuel supply. The distinctive red power switchplate can usually be found at the top of the cellar stairs or near the burner itself, while the fuel shutoff valve is near the oil tank or on the incoming gas pipe. Note the location of both in case of a future leak or fire.
If your furnace’s motor runs but the blower doesn’t move air, the belt that connects the two probably has broken. Replacing it is an easy fix. First, turn off all power to the unit and turn off the gas at the gas valve that serves the furnace. Remove the door on the front of the furnace cabinet to give you access to the blower (it might be on a slide-out drawer.) Check the number stamped on the belt and get an exact replacement from a home center or heating supply outlet.
Our technicians have many years of experience repairing furnaces and will make sure your home is back to keeping you warm and cozy in no time. From training and certifications to our reputation for completing the job right time and time again, you can be sure that B & B Heating & Cooling’s furnace repair technicians will have your problems taken care of and your furnace operating smoothly. Whether it’s emergency furnace repair or service you can schedule some time in advance, our team can provide you peace of mind, knowing that your furnace is in experienced hands. Need a furnace repair? When performing a repair, it's crucial to vet professional HVAC contractors.
No matter how minor you may think that a problem with your air conditioner is, it will eventually lead to more serious problems if given the time. Prompt air conditioning repair service is the best way to limit the damage that any problems with your AC can do. Let our Puyallup air conditioning repair technicians get your AC back on track in no time.
“Walter Zainey started the Greenwood Furnace Co. in the Greenwood neighborhood of Seattle in 1918 and quickly built a reputation for providing quality products and services. For years we believed Greenwood began in 1921 but only recently, May of 2017, Walter’s granddaughter shared a newspaper ad from 1968 showing that Greenwood was actually founded in 1918! When your company goes back 100 years you are bound to have mixed messages about the history but we now have an accurate founding date and founder. Thank you to the Zainey family and especially Jacklyn for taking the time to share the story with us. I am sure Walter Zainey would be proud the heritage he created is still living on.
When’s the last time you had your home’s heating system maintained? If you’re like most homeowners it’s probably been a while, but keeping your plumbing, heating, and cooling systems under control is vital. That’s where Anthony Plumbing, Heating and Cooling comes in. We’re the best in HVAC Service in Kansas City, MO when it comes to keeping your systems running and your family comfortable. Our company was founded in 1951 and we’ve been providing quality services in Kansas City ever since.We service and do repairs in the following: Kansas City KS Furnace Repair Air Conditioning, Plumbing
The thermocouple is a copper rod that the pilot flame heats-up. When it gets hot enough, the thermocouple signals that there is enough heat to burn the gas fuel being released into the appliance—and so it allows the gas to be released to the burners. In some cases where the pilot light won’t stay lit, the thermocouple needs to be adjusted or replaced. This is generally a job for a professional.
2Be sure the furnace’s circuit breaker is on or that its fuse has not blown. Check both the main electrical panel and any secondary subpanels that supply power to the unit. If the circuit has blown or tripped, reset the circuit breaker by flipping it all the way off and then on again. Or replace the fuse. If the circuit blows again, there is probably a short in the electrical system providing power to the furnace. For this, you may need to call an electrical contractor.

An annual inspection of your unit can ensure that the various potential problems mentioned above are detected early, and before they require complete replacement. During this inspection, for instance, a professional might find small cracks in your heat exchanger or a faulty seal in your blower motor. Some manufacturer's warranties even require these annual inspections to maintain validity. Typically, your furnace inspection will cost between $80 and $150 depending on the area in which you live and the professional you work with.
House of Heating Incorporated offers furnace service appointments that help keep your furnace in excellent shape and running efficiently for you all year long. Whether that’s discovering small issues before they become big problems, identifying potential safety hazards or making sure you’re staying in line with your manufacturer’s warranty, our experts have you covered. Our trained technicians complete furnace service with skill, inspecting a number of components in and around your furnace. In fact, our multi-point inspection can help make sure your system works smoothly throughout the winter.

Whether you’re looking to have a heat pump installed for the first time or think it’s time for an upgrade to your current system, Goettl Air Conditioning is the company to call. We offer a great lineup of Phoenix heat pumps and will make sure that the one we install in your home is the recommended match to your home’s dimensions and your family’s needs.
Looking for a local and trusted air conditioning and heater expert that is nearby? HVACs Today is here to help. Keeping your home or business heated or cooled is what we are great at. From installation to replacement and repairs, our technicians can complete your job quickly and correctly. Skilled contractors can solve your HVAC needs: no problem is too big or too small. Call us today to schedule your heating and cooling service.
Great article! I am having trouble identifying what to use for the aluminum or zinc strips to prevent organic growth and staining. How wide are the strips? Are they predrilled? I am starting to see black stains on the north facing asphalt shingles. Do you recommend treating that befor adding the metal strips? If so, 50/50 bleach and water or a commercial product?

Heating Repair Company

×