Do you need expertise in HVAC? Roswell and Marietta residents who choose Moncrief Heating & Air Conditioning get the benefit of over 118 years of reputable experience in air conditioning and furnace repair, service and installation. Whether you have an emergency or need routine service, we are available 365 days a year. Call us today at 404-350-2300.


For starters, once a year, vacuum out the area around the furnace’s blower. If possible, also slide out the fan unit, clean each fan blade with a toothbrush, and then vacuum with a brush attachment on a vacuum cleaner. While you’re at it, look for oil ports on the motor, normally located near the motor shaft. If the motor has these, apply two to three drops of non-detergent motor oil into each port (you may have to remove a cover plate to do this). Though most contemporary motors don’t require lubrication, do lubricate motors with oil ports once a year. For more about maintenance, see Maintenance Checklist for Central Heating Systems.

With our furnace service, your burners will be pulled and cleaned. To ensure the best possible efficiency, we can adjust your heat-off delay. You can also expect a combustion analysis performed by a professionally certified HVAC technician. With a proper combustion analysis, we’ll be able to tell you if your furnace is operating at maximum efficiency and keep you safe.
Another energy savings tip, HVAC professionals say, is using a programmable thermostat. A programmable thermostat can save you up to 10 percent on energy bills, if you dial it down seven or eight degrees from the normal temperature setting — the U.S. Department of Energy recommends a setting of 68 degrees — for eight hours a day, whether it's during the work day or at night, according to DOE.
As a Carrier Factory Authorized Dealer, M and M, Heating & Cooling, Plumbing & Electrical is qualified to properly size and install the most technologically advanced and well-regarded heating, cooling, and air quality products on the market today. Our team is NATE-certified, factory trained, EPA certified, and regularly updated, ensuring the right solution to any challenge.
Vredevoogd Heating & Cooling is Michigan’s top Heating & Air – Furnace Repair & Replacement – Air Conditioning Repair and installation service. With decades of experience and expertise, Vredevoogd Heating & Cooling remains committed to offering affordable 24/7 service. Our skilled heating and cooling specialists are certified and background checked. Our team is here when you need us to meet all your heating and cooling needs.

The cost to replace your entire unit is around $4,000. That expense can range from $2,500 to $5,900, depending on the type and brand of furnace you choose. Brands particularly have an impact on that price. A Goodman electric furnace, will only cost about $2,100 for the unit and labor. On the other hand, a Trane oil furnace may cost up to $9,000 all things considered. Our Furnace Installation Cost Guide can give you a better idea on both the general cost and the differences for brands like Amana, Bryant, Coleman, and others. The brand also plays into the repair cost for your furnace. Especially the prices of individual parts can change; a York heat exchanger, for example, can cost up to $1,900, while the same component from Heil will cost as little as $400.
Marky Mark's Heating, Cooling & Plumbing, LLC offers a range of residential and light commercial HVAC services in Thornton, CO & Westminster, CO. Call 720.961.4016 to request an emergency repair, schedule yearly maintenance, or get a free estimate on a new furnace or air conditioning system. Our team of licensed HVAC technicians can address all makes and models. We offer quick turnaround, competitive pricing, innovative products, and high quality service. When temperatures start to change in Thornton, CO & Westminster, CO and the Northern Denver Metro area, call on the heating and cooling experts at Marky Mark's Heating, Cooling & Plumbing, LLC.

Your furnace's flame sensor is essentially a safety mechanism. As a thin metallic rod in front of the flame inside the unit, it's sole purpose is to confirm that your gas valves only open when a flame actually exists to burn that gas. When the flame sensor stop working, on the other hand, gas leaks can occur. To repair your furnace's flame sensor, expect to spend between $80 and $250. Even a full replacement of this part typically does not go above that range.


So the furnace went out (again). We’re probably not the people you want to be dialing, but in these circumstances, Service Experts Heating & Air Conditioning in North America should be your very first call. You don’t even have to worry how late (or early) it is – our NATE-certified technicians available at all hours, every day of the year. We’ll be there in a jiffy and get the job done fast – so you can get back to your routine and not have to even think about needing another furnace repair anytime soon.

@Neil What is the use of repeating lessons when there is so much more to be learned? Technology has moved on from the adz. Plumbers use PEC, insulation is sprayed, glue-lams allow for open floor plans and furnaces are no longer stoked with coal. As for the new people, if these trades cannot attract fresh blood we will all be unable to get homes built and repairs made. I don't yearn for my first home with the leaky concrete block foundation, failing well pump and an oil furnace held up by the plenum. I'll take heat pumps, solar panels and PVC waste pipes any day.You can get all the sill plate repairs and flitch beams demos you need on YouTube.

I was disappointed with the pressure of a tub and shower that were plumbed with 1/2 supply lines (2nd floor). Could be low pressure from the street, but I want to replace with 5/8. Plus, I'd like to have 2 back to back showers, one inside and one outside. So, I had intended to bring a 1 supply to both, then branch up to valves and shower head with 5/8. Finally, I thought pressure from the street was typically 55 to 70 psi and I am concerned if pvc can take that.Any thoughts?
Great article! I am having trouble identifying what to use for the aluminum or zinc strips to prevent organic growth and staining. How wide are the strips? Are they predrilled? I am starting to see black stains on the north facing asphalt shingles. Do you recommend treating that befor adding the metal strips? If so, 50/50 bleach and water or a commercial product?

Heating Repair Company

×