Regarding your post, Every technician performs a maintenance differently. Today's modern furnaces really don't require as much maintenance as older style systems did. For instance: Older furnaces had drive belts, pulleys and motors with oil ports.Today's blowers are direct drive no belts, no pulleys, sealed bearing motors no oiling required. All of the new modern technology cuts the maintenance time in half if not more. Today's equipment has multiple safety's in place so that in case of a failure the system will shut down. non serviceable control boards or (Brains) monitor system functions. Unlike oil systems, the maintenance on a gas system can possibly be completed in less than half the time. I'd say 20 to 30 minutes is about right unless a service issue arises. In the 30 minute time span, the doors can be removed, system components can be visually inspected, the flame can be inspected and co test can be performed for spillage and vacuum of the combustion area can be performed if needed. The air filter should be checked and the humidifier can be activated. Remember that probing into a perfectly functioning system can be detrimental to its lifespan. My advice is change you air filter, keep the area around the equipment free of dust and try not to store in close proximity to the heating plant. Be sure you have an updated quality carbon monoxide detector in your home. Regarding the crack in your heat ex-changer, If the heat ex-changer had a crack in it, the system it should have been shut down right then and there. Be aware that Carbon monoxide may be entering your living space due to that crack. Have a knowledgeable company come back and do a CO test in your home at the supply vents and use a scope to check your heat ex-changer for cracks. I hope this helps you. Bottom line, you have to trust the company that you are using. If you feel uncertain about their capabilities, then more than likely, you instinct is correct. Good Luck to you.. Happy Holidays
Do not try to do DIY gas furnace maintenance or tune-ups yourself. In addition to being dangerous, this may also violate the manufacturer’s warranty. Let properly trained and experienced technical staff perform all gas furnace preventative maintenance. Regardless of your DIY talent, trying DIY furnace maintenance is fraught with hazards and risks to your heating system—and yourself.

Looking for a local and trusted air conditioning and heater expert that is nearby? HVACs Today is here to help. Keeping your home or business heated or cooled is what we are great at. From installation to replacement and repairs, our technicians can complete your job quickly and correctly. Skilled contractors can solve your HVAC needs: no problem is too big or too small. Call us today to schedule your heating and cooling service.
As a Carrier Factory Authorized Dealer, M and M, Heating & Cooling, Plumbing & Electrical is qualified to properly size and install the most technologically advanced and well-regarded heating, cooling, and air quality products on the market today. Our team is NATE-certified, factory trained, EPA certified, and regularly updated, ensuring the right solution to any challenge.
The cost to replace your gas furnace will vary based on the type and size of furnace you select, labor and installation costs, and any repairs your HVAC system may need. Nationally, average HVAC prices for a heating specialist range between $1,800 and $2,500. It’s important to select the right size gas furnace for your heating needs. A furnace that’s too small won’t heat your house properly, while a furnace that’s too large will run inefficiently, cycling on and off and likely breaking down sooner. HVAC specialists calculate your exact heat needs by measuring your home and incorporating variables such as the regional climate and your home’s level of insulation. Retail pricing for gas furnaces can range from $650 up to $3,000 and more. The higher the AFUE (annual fuel utilization efficiency) rating of the furnace, the more efficient it is at turning fuel into heat and the lower your carbon footprint and utility bill will be. HVAC installation costs are often based on an hourly rate and can range from under $50 to over $100 per hour, depending on the company and the furnace being installed. Higher-end furnaces cost more to install because they require added labor and expertise. For a typical installation, it might take two HVAC installation pros one day or less to remove your old furnace and replace it with a new one.
If your furnace has a pilot light, look for the flame. Check your owner’s manual or the instructions posted inside the furnace cabinet for step-by-step lighting instructions. Usually this involves first turning the gas valve to Off and waiting a couple of minutes. Then you turn it to Pilot. Next, press and hold it down while you light the flame. Last, wait a minute or so, release it, and then turn it to On.
You might guess it from the name: the heat exchanger is the part of your furnace that actually heats the air your blower motor pushes through the furnace. It consists of a chamber in which the heat energy produced by natural or propane gas is transferred to the forced air. At the same time, this part also includes a vent through which the gases themselves are safely removed from the unit and the air that enters your home. Because of these gases, a problem with your heat exchanger needs to be dealt with promptly. Over time, cracks in the exchanger can result in carbon monoxide leaks. Taking care of the problem once again means understanding the existence of a range: repairing your heat exchanger can cost as little as $100, but a full replacement may cost up to $1,200.
An annual inspection of your unit can ensure that the various potential problems mentioned above are detected early, and before they require complete replacement. During this inspection, for instance, a professional might find small cracks in your heat exchanger or a faulty seal in your blower motor. Some manufacturer's warranties even require these annual inspections to maintain validity. Typically, your furnace inspection will cost between $80 and $150 depending on the area in which you live and the professional you work with.
Modern high-efficiency furnaces not only provide superior heating, they save money on energy bills, last longer and generate less noise. The hands-on experience, technical expertise and dedication of the team from Choice Heating & Cooling ensures that your new equipment operates at peak performance, providing consistent enjoyment for years to come. To further protect your investment, Choice Heating & Cooling offers prompt repair and comprehensive maintenance, delivering consistent warmth at fair prices.

Before performing DIY furnace maintenance, Richard makes sure to switch off the electrical power and the fuel supply. The distinctive red power switchplate can usually be found at the top of the cellar stairs or near the burner itself, while the fuel shutoff valve is near the oil tank or on the incoming gas pipe. Note the location of both in case of a future leak or fire.


We’re located in Marshfield and service the surrounding area, so stop on by if you’re searching for a new furnace or want to set up an appointment to have one of our techs visit your home and help you learn which system is best for your home. Schedule furnace repair or a furnace service appointment with House of Heating Incorporated using our online scheduler, or if you want help more quickly, give us a buzz at 888-384-3163. 

Though forced-air furnaces are normally quite reliable, they can break down. To avoid break downs, it pays to know how to take care of your furnace and fix it when something goes wrong. Inevitably, a furnace stops working when you need it most. Consequently, fixing becomes urgent very quickly. The following instructions will help. With a little do-it-yourself experience and the proper guidance, you can troubleshoot and repair a variety of furnace problems yourself.


If your furnace’s motor runs but the blower doesn’t move air, the belt that connects the two probably has broken. Replacing it is an easy fix. First, turn off all power to the unit and turn off the gas at the gas valve that serves the furnace. Remove the door on the front of the furnace cabinet to give you access to the blower (it might be on a slide-out drawer.) Check the number stamped on the belt and get an exact replacement from a home center or heating supply outlet.
2Be sure the furnace’s circuit breaker is on or that its fuse has not blown. Check both the main electrical panel and any secondary subpanels that supply power to the unit. If the circuit has blown or tripped, reset the circuit breaker by flipping it all the way off and then on again. Or replace the fuse. If the circuit blows again, there is probably a short in the electrical system providing power to the furnace. For this, you may need to call an electrical contractor.
When your furnace isn’t regularly serviced it can operate less efficiently. This increases your energy bills and also prevents your furnace from keeping your home as warm as you like. Keep your furnace properly maintained with regular service. The national average furnace service cost is between $60 and $80. Companies may offer tuneup specials that cover all the necessary testing, tightening, measuring and cleaning to keep your equipment running at top efficiency. If you have a newer system, furnace service costs may be covered by your warranty. Outside of warranty, a basic tuneup might start at $58 and a more advanced maintenance cleaning could be over $120. Here are some signs your furnace may need service:
• Furnace is making more noise because it’s turning on and off more frequently. It may need repair, may not have been sized properly to fit the needs of your house, or may not have the airflow available that it needs from the ducts. The ducts are most often the culprit. Sometimes adding a cold air return can solve this. Ensure your vents are all open. If you are closing off vents in your house this can contribute to the issue.
If your thermostat has a small lever that moves along a calibrated scale that indicates “longer” (not the heat temperature lever), you can try adjusting this—the heat anticipator. Just set it one calibration mark closer to the “longer” setting if the furnace goes off and on too frequently or one mark away if the furnace allows room temperature to rise too high or drop too low before going on or off. It may take several hours for the thermostat to stabilize at this setting, so wait a while and then adjust it again if necessary.
We asked This Old House plumbing and heating expert Richard Trethewey to show us the proper steps that a service professional would follow for an oil-burning forced-air furnace; the basics on a gas system are similar. In both, fuel is mixed with air and ignited, heating a sealed chamber. Fresh, filtered air then blows across the outside of the hot chamber and into the heating ducts. (Homes with radiators have boilers instead of furnaces. These heat water instead of air, but the annual checkup is similar.) In all, the dangerous exhaust from the combustion chamber is vented out a flue or chimney.

Furnace Repair Company CO

×