Your furnace's flame sensor is essentially a safety mechanism. As a thin metallic rod in front of the flame inside the unit, it's sole purpose is to confirm that your gas valves only open when a flame actually exists to burn that gas. When the flame sensor stop working, on the other hand, gas leaks can occur. To repair your furnace's flame sensor, expect to spend between $80 and $250. Even a full replacement of this part typically does not go above that range.
CM Heating performed a Gas Furnace Diagnostic. Customer wanted his echo bee thermastat installed that he had bought himself. Furnace was working fine just wanted his thermastat installed. He thought that the $99 service fee was going to cover that but explained to him what the service fee was for, and explained that there is a additional install fee for the stat. Customer didn’t want to pay the additional fee so I called the office had them listen to the call to make sure we explained to the customer correctly and to see how they would like me to proceed. So I quoted the customer the fee to install the thermostat but he didn’t want us to install it so I left.
Don’t forget, when you’re in the need for 24 HR emergency repair in Akron, Ohio, Jennings is there for you no matter the time of day or night—24 hours a day and 7 days a week. If you have an emergency, please call 330-784-1286 now. If you would like to request service, please fill out and submit the form below and a Jennings associate will be in touch make an appointment.
"During the winter, all the air that your family is breathing comes through this filter," says Richard. "You can't change it too often, but never let it go for more than a year." Changing the filter is something any homeowner can do easily. At the same time, Richard checks the blower belt's wear and tension. (The blower, driven by an electric motor, moves heated air from the furnace through ductwork to room vents.) A loose belt can slow the blower, compromising efficiency. If the belt deflects more than ¾ inch when pressed firmly, it can be adjusted by sliding the motor backward slightly.
There are a lot of problems you may encounter with your water heater, but there are also a lot of warning signs that can tip you off to the fact that repairs are necessary. Unreliable or insufficient hot water, as well as increased hot water costs, are among the most common. Give us a call to ensure that your water heater repair in Kirkland, WA is completed promptly.
While there's nothing you can do to guarantee your air conditioner or furnace will never need repairs, there are ways to take better care of your system. Changing out the air filters every 3-6 months, making sure nothing is obstructing or interfering with the outside unit, and keeping all vents unblocked in well-used rooms will help keep your air conditioning and heating system operating efficiently.

We’re located in Florissant and service the surrounding area, so feel free to swing by if you’re searching for a new furnace or want to set up an appointment to have one of our techs visit your home and help you figure out which system is ideal for your home. Schedule furnace repair or a furnace service appointment with B & B Heating & Cooling using our online scheduler, or if you’re in need of help a little more quickly, give us a call at 314-838-9800. 
Sometimes a heating and air conditioning system just needs to be repaired rather than completely replaced. You may need air conditioning repair services if there is leaking around the outside unit, the air coming into the house isn't hot or cool enough, the unit is short-cycling or constantly turning on and off, using the system is consistently resulting in higher-than-normal energy bills, or if there is excessive noise during startup and operation.
Having a company looking out for all your heating and cooling needs shouldn’t mean that you’re stuck with any run-of-the-mill shop who cuts corners. Heating and cooling has been our excitement since 1962, and it’s evident in the work we provide to our customers. We’re committed to providing you the very greatest when it comes to all things HVAC, whether it’s service, maintenance or heating and cooling systems.
Before performing DIY furnace maintenance, Richard makes sure to switch off the electrical power and the fuel supply. The distinctive red power switchplate can usually be found at the top of the cellar stairs or near the burner itself, while the fuel shutoff valve is near the oil tank or on the incoming gas pipe. Note the location of both in case of a future leak or fire.
Finally, don't underestimate the thermostat as a potential reason why your furnace is not working. Everything on the heating unit itself may function perfectly, but your home still will not heat right if the console you use to set the temperature doesn't communicate your input. A faulty thermostat can either be due to the wall unit itself, or the wiring that connects it to your furnace. Average thermostat repair costs are between $108 and $282, including labor. Replacement costs, of course, depend on the thermostat you choose. Visit our thermostat repair cost guide to learn more about this type of issue.
In order to make your everyday life easier and more enjoyable, Sky Heating & Air Conditioning specializes in state-of-the-art heating and cooling technology, partnering with Trane, Mitsubishi, and Waterfurnace.  We bring you HVAC solutions that represent the best the industry has to offer, ensuring long-term performance and satisfaction.  Whether you’re looking for the design/build of a new system, replacement, or hoping to cut costs and enhance convenience, we answer with proven products.  Our qualified HVAC technicians help you determine the ideal solution for your exact requirements, and make sure you’re happy with every step of the process.  From ductless HVAC to geothermal heating and cooling systems, we offer a wide selection of options and comprehensive services to answer any type of challenge.  Call on Sky Heating & Air Conditioning and let us exceed your expectations today!
CM Heating performed an electric furnace Diagnostic - Upon investigation, I found that the sequencer has failed which is why all heat elements are not being activated (3 out of 5 work). This is the second replacement sequencer needed in less than 5 years of operation, the unit is an old model of air handler and only source of heat. Replacement of sequencer is needed, however, based on age and efficiency recommend upgrade of system.
Zolie and Charely were very professional and on time.They gave us an estimate to replace our water heater and went over all our options.We opted to have them install a new water heater and get things up to code. Within three hours we had a new water heater installed. Zolie and Charley were efficient and pleasant to work with. We were pleased with the work that was completed!

Cleaning the debris that builds up on your filters will aid with the flow of air. When your air filter is clogged, your air handler must work harder to compensate for the blockage of air flow. In addition to driving up your utility bill, the reduced air flow through your heating and cooling system can cause your heat exchanger to overheat and shut off too quickly.    
×