You can usually slip the belt on the motor’s (smaller) pulley first and then start it on the blower pulley. Rotate the blower pulley by hand, holding the belt in place but keeping your fingers from getting caught between the belt and the pulley. The belt should slip right into place. If it seems to be too tight or difficult to set in place, it may be necessary to adjust the motor mount to provide more slack.
Specializing in Bryant brand heating and cooling products, we offer a broad selection of innovative, industry leading technology to improve the comfort, health, and efficiency of your home or office. Our technicians are certified and highly trained to provide residents in Thornton, CO & Westminster, CO with unmatched heating and air conditioning services, including installation, repair and maintenance. Plus, our team of plumbers offers a range of indoor and outdoor plumbing solutions, including repair and installation of faucets, fixtures, water heaters and toilets, frozen pipe prevention and repair, and natural gas line service. Give us a call and take advantage of our proven dedication and prompt response. 

Furnace Repair Company


High-efficiency condensing furnaces (90% AFUE and above) are a bit more complex than conventional furnaces. The main differences between a conventional and condensing furnace are the heat exchanger technology used to extract heat from the combustion process and the method used to exhaust the combustion gases. In these ways, the furnaces are very different. The condensing furnace does not have a significantly more efficient combustion process than does a conventional furnace; both use gas burners with electronic ignition. The difference lies in that the condensing furnace has a more efficient heat extraction process after combustion.
When a furnace maintenance is performed a combustion analysis should be performed to identify any problems that couldn't be found by a visual inspection. You want to know what the Carbon monoxide level your furnace is producing as well as the oxygen/CO2 levels and stack temperate. The analyzer will also give you a calculated efficiency rating with the information the analyzer receives. You should have >100ppm of Carbon monoxide output during normal operation of your gas furnace. When you have higher numbers or CO numbers increasing during operation their is a problem with the furnace the technician should then find the cause of. This is just a brief explanation I'm trying to get across to those who get their furnace maintained and to those who don't! Check to see if anyone in the company has a NCI certification for carbon monoxide/combustion analysis.
Another energy savings tip, HVAC professionals say, is using a programmable thermostat. A programmable thermostat can save you up to 10 percent on energy bills, if you dial it down seven or eight degrees from the normal temperature setting — the U.S. Department of Energy recommends a setting of 68 degrees — for eight hours a day, whether it's during the work day or at night, according to DOE.

Richard sets up a combustion analyzer, which calculates furnace efficiency by measuring gasses in the exhaust flue. He makes sure that the burner's air gates are adjusted for the proper ration of fuel to air. "You want the fuel that you've brought to the be burned before it goes up the chimney," Richard says. He also replaces the oil nozzle, which atomizes the fuel just before it ignites, and checks the flame color and shape at the igniter. For either oil or gas, this is a key indicator of stable and complete combustion. In a gas system, this is the time when the burner tubes should be vacuumed clean.
“The manufacturers that built them all agree on this; you should get it serviced once [a year] for heating and once for cooling," says Paul Mills, owner of Air Experts Heating & Cooling in Raleigh, North Carolina. "Tuning it up and checking it out is definitely recommended. Much like a car, if you ignore it, a lot more things break. You [will] extend the life of it and help prevent major breakdowns.”
We’ve earned a reputation across Portland and The Dalles for dedicated customer service.  Consistently maintaining an A+ rating from the Better Business Bureau, Sky Heating & Air Conditioning meets higher standards of excellence through the little, important details that add up to a job well done.  It starts with a friendly voice on the phone, and the immediate focus of our extensive resources on your requirements.  From there, you can count on timely arrival, organized project management, careful cleanup, competitive pricing, and exemplary performance in every aspect of service.  When you contact Sky Heating & Air Conditioning for HVAC service in The Dalles and Portland, OR, your project is always handled by a highly-trained professional, who will achieve your goals for efficiency, reliability, and sustainable home comfort.
BGE HOME HVAC repair technicians are thoroughly trained and certified to work on all major brands of heating and air conditioning equipment. When your system breaks down and needs a heating and air conditioning repair, you want to call someone you can trust. Need air conditioning service in the middle of the night? Emergency heating and cooling HVAC service is available 24 hours a day by calling 888-243-4663.
As touched on by their name, heat pumps function by transferring heat energy indoors during the winter and outdoors from your home during the summer. They're often attached to air conditioning units, using the surrounding air to transfer energy. However, geothermal heat pumps and water source heat pumps are also available. The cost to repair a heat pump, again, depends on the specific problem. Replacing a faulty thermostat may cost up to $300 including labor, while a worn or damaged defrost control board can set you back up to $600. For more details on your potential repair costs using this heating source, visit our heat pump repair cost guide.
• Furnace is making more noise because it’s turning on and off more frequently. It may need repair, may not have been sized properly to fit the needs of your house, or may not have the airflow available that it needs from the ducts. The ducts are most often the culprit. Sometimes adding a cold air return can solve this. Ensure your vents are all open. If you are closing off vents in your house this can contribute to the issue.
AAA Heating and Cooling has been the leader in residential and commercial furnace installation, heating services and air conditioning repair for thousands of clients throughout Portland, Beaverton, Hillsboro, Lake Oswego and the surrounding areas for over half a century. As a family-owned Portland, OR business, we offer a variety of services, including the installation of home heating and air conditioning systems, AC and furnace service and repair, duct cleaning as well as a variety of commercial heating and cooling solutions.
Service Experts Heating and Air Conditioning was founded on the basis of providing customers with the best heating and cooling practices in the industry. Since its inception, Service Experts has been dedicated to community, providing the top of the line HVAC products and services in your area. If you want more information about your local HVAC leaders, call us at 866-397-3787 or set up an appointment with us online.

You should never wait for your furnace to break down completely before scheduling professional furnace repair service in Kirkland, WA. The best way to handle any furnace repair needs is to contact a repairman at the first sign of trouble. If you notice a spike in heating costs, your furnace is not heating your home evenly, or it makes strange and unusual sounds, then it’s time to bring in a qualified Kirkland furnace repair technician.

Most manufacturers’ warranties call for annual equipment maintenance to stay valid, so missing your tune-ups can possibly result in losing your heating or AC system warranty, which can be major money if your equipment does ever stop working in the middle of a cold snap. Make sure you get all you can from your warranty by making sure it stays valid as long as possible with annual furnace system tune-ups from Service Experts.

Advice you can count on – When you have an emergency, you are not always in the position of asking questions to determine if the repairs you are receiving are what you need. At Jennings, our NATE Certified technicians will walk you through the repairs and explain why you need them. You can trust that everyone on Jennings’ staff will give you honest advice.
Natural gas furnaces operate similarly to the above, using a pilot light to ignite the burners and heat up the air. Also similar to propane gas, your average repair costs for a natural gas furnace will range anywhere from $125 for small repairs to $1,200 if you have to replace the entire heat exchanger. The difference between both options is not necessarily the actual furnace, but the type of gas used to burn through it and heat your home. As a result, the repair costs tend to be close to identical.
Call us today at (302) 200-4266 today to schedule a service heating system repair, replacement, installation, or tune-up services with our capable team! our team! We offer honest, upfront pricing in writing and industry leading warranties on parts and service. Find your local Horizon today to schedule heating system repair, replacement, installation, or tune-up services with our capable team!

The oil filter (found in oil-powered systems only) prevents small impurities from clogging the oil-burner nozzle, which could result in a misfire that shuts down the system. Richard first closes the oil valve, then removes the old filter and replaces it, setting aside the dirty filter to be disposed of according to local hazardous-waste regulations.
When your furnace isn’t regularly serviced it can operate less efficiently. This increases your energy bills and also prevents your furnace from keeping your home as warm as you like. Keep your furnace properly maintained with regular service. The national average furnace service cost is between $60 and $80. Companies may offer tuneup specials that cover all the necessary testing, tightening, measuring and cleaning to keep your equipment running at top efficiency. If you have a newer system, furnace service costs may be covered by your warranty. Outside of warranty, a basic tuneup might start at $58 and a more advanced maintenance cleaning could be over $120. Here are some signs your furnace may need service:
×